Eiki/Elf EIP-4500 setup guide Projector Master, Slave

Page 40

Stack Projection

6 Connect the INPUT 1 terminal on the projector 1 to the RGB output terminal on the computer using the RGB cable.

(See page 27 on the owner’s manual of the projector.)

7 Connect the OUTPUT (FOR INPUT 1, 2) terminal on the projector 1 to the INPUT 1 terminal on the projec- tor 2 using an RGB cable.

(See page 36 on the owner’s manual of the projector.)

Note

•When connecting an RGB cable to the pro- jector 2, use the input terminal that has the same number as the projector 1. (IN- PUT 1 terminal, in this case)

8 Connect the LAN terminal on the projector 1 to the LAN terminal on the projector 2 using a commer- cially available LAN cable (UTP cable, Category 5, cross-over type).

9 Turn on the projectors first, then turn on the computer.

Application

When inputting multiple image sources, refer to the example below.

INPUT 1 terminal

RGB cable

Projector 1

Projector 1:

Master

INPUT 2 terminals INPUT 4 terminal

OUTPUT (FOR INPUT 1, 2) terminal

LAN terminal

Computer

Master

Set Inputs

INPUT1	ON
INPUT2	ON
INPUT3	OFF
INPUT4	ON
INPUT5	OFF

	RGB	LAN cable
	cable	LAN cable
	cable	(cross-over		Projector 2
		(cross-over		Projector 2
INPUT 1 terminal		type)		Slave
			5 BNC to 15-pin	Slave
Projector 2:			5 BNC to 15-pin	Set Inputs
			D-sub cable	Set Inputs
			D-sub cable	INPUT1	ON
Slave				INPUT1	ON
Slave				INPUT2	OFF
		LAN terminal	Computer	INPUT3	OFF
		LAN terminal		INPUT4	ON
				INPUT4	ON
INPUT 4 terminal				INPUT5	OFF
INPUT 4 terminal
		Distributor
	Composite video cable		Video equipment
			Video equipment

40

Image 40

Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Setting the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredControlling the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set ItemsSave Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name Setting Password SettingProjector Name Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Stack Projection Setting up the Stack Projection Projector 1 MasterProjector 2 Slave Turn off the both projectorsProjector Projector MasterSlave Video Wall Projection HubSetting up the Video Wall Projection Basic Access one of the four projectors via Internet Explorer Click Video Wall on the menuSelect 2 X 2 on Division Click the assigning button for the desired positionAdjusting the Position Horizontally and Vertically Returning to the Default Video Wall SetupAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveChange the TCP/IP settings for the computer as shown below Jectors as shown belowProjector Master Projector 2 Slave Projector 3 SlaveClick Stack on the menu Select Slave on Stack Setting Click Stack on the menu Select Master on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm