Eiki/Elf EIP-4500 setup guide Connecting the Pro- jector to a Computer

Page 18

Setting up the Projector Network Environment

1.Connecting the Pro- jector to a Computer

Establishing a one-to-one connection from the projector to a computer. Using a commercially available LAN cable (UTP cable, Category 5, cross-over type) you can configure the projector via the computer.

1 Disconnect the computer’s LAN cable from the existing network.

A LAN cable being connected to the network

2 Connect a commercially available LAN cable (UTP cable, Category 5, cross-over type) to the projector’s LAN terminal and connect the other end of the cable to the computer’s LAN terminal.

LAN cable

3

4

Turn on the projector.

ON

Turn on the computer.

ON

Info

Confirm that the LINK LED on the side of the projector illuminates. If the LINK LED does not illuminate, check the following :

•The LAN cable is properly connected.

•The power switches of both the projector and the computer are on.

This completes the connection. Now proceed to “2. Setting an IP Address for the Com- puter”.

18

Image 18

Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments RS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralMail Recipient Settings Input setup and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredVView All Setting Controlling the Projector Using RS-232C or TelnetView Setting Detail List Set ItemsSSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting Projector Name Setting User Name SettingPassword Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Stack Projection Projector 2 Slave Setting up the Stack ProjectionProjector 1 Master Turn off the both projectorsProjector Master ProjectorSlave Video Wall Projection HubSetting up the Video Wall Projection Basic Select 2 X 2 on Division Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Click the assigning button for the desired positionAssigning the Projected Image on the Video Wall Setup Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveProjector Master Projector 2 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector 3 SlaveClick Stack on the menu Select Master on Stack Setting Click Stack on the menu Select Slave on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm