Hitachi CP-X5021N Replacing the internal clock battery, Maxell , part number CR2032 or CR2032H

Page 93

Maintenance

Replacing the internal clock battery

This projector has internal clock that uses a battery. When

the clock of the network function does not work correctly,

OPEN

CLOSE

 

please try solution by replacement of the battery: HITACHI

 

 

MAXELL, part number CR2032 or CR2032H.

 

 

1.

Turn the projector off, and unplug the power cord. Allow

 

 

the projector to cool sufficiently.

 

 

2.

After making sure that the projector has cooled

Raised dot

adequately, slowly turn over the projector, so that the

Knob

 

bottom is facing.

Battery

3. There is a raised dot near the battery cover at the bottom of the projector. Turn the cover in the direction indicated OPEN to position one end of the slit on the cover with the dot, using a coin or the like. And then pick the cover up to remove it.

4. Pry up the battery using a flathead screwdriver or the like to take it out. While prying it up, put a finger lightly on the battery since it may pop out of the holder.

5. Replace with a new battery of the specified type. With the plus side facing up, slide the battery under the claw of the spring fitting. And press down on the battery until it snaps into place.

6. Replace the battery cover in place, then turn it in the direction indicated CLOSE to position the knob of the cover with the dot on the bottom case to fix the cover, using a coin or the like.

OPENCLOSE

Battery

Cover

EOSCL

OPEN

CLOSE

OPEN

NOTE • The internal clock will be initialized by removing the battery. For setting the clock, see the User’s Manual - Network Guide.

WARNING ►Be careful of handling a battery, as a battery can cause explosion, cracking or leakage, which could result in a fire, an injury, and environment pollution.

Use only the specified and perfect battery. Do not use a battery with damage, such as a scratch, a dent, rust or leakage.

When replacing the battery, replace it with a new battery.

When a battery leaked, wipe the leakage out well with a waste cloth. If the leakage adhered to your body, immediately rinse it well with water. When a battery leaked in the battery holder, replace the batteries after wiping the leakage out.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Do not work on a battery; for example recharging or soldering.

Keep a battery in a dark, cool and dry place. Never expose a battery to a fire or water.

Keep a battery away from children and pets. Be careful for them not to swallow a battery. If swallowed consult a physician immediately for emergency treatment.

Obey the local laws on disposing a battery.

93

Image 93
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Checking the contents of package FeaturesProjector Part namesRear panel 10 ~ LAN port Control panel and Lens adjustersControl port Audio IN1 portDown button Volume + button Remote controlComputer button STANDBY/ON buttonSetting up ArrangementCP-X4021N, CP-X5021N 1610 CP-WX4021NScreen Projection Screen height Size Distance Projection Screen height DistanceDo not place the projector on a metal stand About Plug-and-Play capability Connecting with your devicesComputer Connecting with your devicesUSB Computer Access pointStorage DeviceDigital VCR/DVD/Blu-ray Disc player Video Device Microphone Wired System Remote Control Optional Microphone functionSpeakers Monitor Using the security bar and slot Connecting to a power supplyPower cord Anti-theft chain or wire Security bar Security slotInstalling the batteries Remote controlAbout the remote control signal Hitachi MAXELL, Part No.LR6 or R6PUsing as a simple PC mouse & keyboard Changing the frequency of remote control signalPower on/off Turning on the powerTurning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundComputer button Press the MY Source / DOC. Camera button onVideo button MY SourceFor a computer signal Searching an input signalFor an Hdmi signal Selecting an aspect ratioAdjusting the projector’s elevator Focus ring Zoom ring Lock Horizontal adjuster lock Adjusting the lensHorizontal VerticalAdjusting the position Using the automatic adjustment featureAuto Correcting the distortionPerfect FIT Magnify ON/OFF button Using the magnify featureTemporarily blanking the screen Temporarily freezing the screenFreeze button Blank buttonUsing the menu function Easy MenuAdvanced Menu Indication Meaning Indication in OSD On Screen DisplayAspect Picture ModeAuto Keystone KeystoneReset ECO ModeMirror Filter TimeBrightness Picture menuContrast GammaColor Temp ColorTint Presentation Theater OFF SharpnessActive Iris SAVE-1, SAVE-2, SAVE-3, SAVE-4For a computer signal For an Hdmi signalImage menu USB Type B or Hdmi port PositionAuto Adjust PhaseSize ExecuteTV Film OFF Input menuHigh MID LOW Video NRVideo Format Hdmi FormatHdmi Range Computer Auto Sync on G OFFFrame Lock On OFFResolution Setup menu Auto ECO Mode Normal ECONormal Hinvert Vinvert H&VINVERT Normal Saving Audio menu VolumeSpeaker Audio SourceMIC Volume Hdmi AudioMIC Level English Français Deutsch Español Screen menuBlank Start UPCapturing error has occurred. Please try again MyScreenMyScreen registration is finished No Input is Detected MyScreen LockSync is OUT of Range Invalid Scan FreqSource Name Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3 TemplateDisplay Description Closed CaptionMode ChannelOption menu Direct PowerAuto Search AutoAuto Power OFFUSB Type B Cancel OK Lamp TimeAir filter MY Button Video S-VIDEO Component Hdmi USB Type B Computer IN1 Computer IN2 LAN USB Type aFAN Speed ServiceGhost Filter MessageKEY Lock Control Panel Remote ControlRemote Freq 1NORMAL 2HIGHCommunication Type Serial SettingsBaud Rate ParityResponse Limit Time Transmission MethodStack Information Factory ResetSetup Dhcp Network menuDynamic Host Configuration Protocol Setup Gateway DefaultIP Address SubnetProjector Name AMX D.D MY ImagePresentation QuitUser Name Multi PCGuide Security menu PasswordEnter the Security menu SecurityTurning on the MyScreen Password Turning off the MyScreen PasswordMyScreen Turning on the PIN Lock PIN LockTurning off the PIN Lock If you have forgotten your PIN codeTransition Detector Turning on the Transition DetectorTurning off the Transition Detector MY Text Password Turning on the MY Text PasswordTurning off the MY Text Password MY Text IndicatorWriting Stack LockPC-LESS Presentation Presentation toolsSupported storage media Supported formatThumbnail mode Button operation Operating by buttons or keysDown Enter InputOperating by the menu on the Thumbnail screen This file seems to be broken or not supported format Full Screen Mode Slideshow mode Return Playlist USB Display Right-Click menu Options window Maintenance Replacing the lampType number DT01171 Replacing the lamp Lamp warning High Voltage High Temperature High PressureType number MU06641 Filter unit Cleaning and replacing the air filterCleaning and replacing the air filter Maxell , part number CR2032 or CR2032H Replacing the internal clock batteryOther care Caring for the cabinet and remote controlInside of the projector Caring for the lensThere is no input signal TroubleshootingAn improper signal is input Related messagesButton operation is not available Internal temperature is risingPower Lamp Temp Regarding the indicator lampsResetting all settings Power Lamp Temp indicator indicator indicator DescriptionShutting the projector down Phenomenon Cases not involving a machine defect Signal source does not correctly workVolume is adjusted to an extremely low level Signal cables are not correctly connectedAudio SOURCE/SPEAKER setting is not correct Brightness is adjusted to an extremely low levelColor Space setting is not suitable Color settings are not correctly adjustedFrame Lock function cannot work on the current Input signal Freeze function is workingSaving function is working Computer cannot start up in the current hardwareCommunication Type for the Control port is Set to Network BridgeEnd User License Agreement for the Projector Software Specifications