Hitachi CP-WX4021N, CP-X5021N user manual Shutting the projector down, Resetting all settings

Page 98

Troubleshooting

Regarding the indicator lamps (continued)

POWER LAMP TEMP indicator indicator indicator

Description

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

Blinking

 

 

Please turn the power off, and allow the projector to cool down at least

 

 

20 minutes. After the projector has sufficiently cooled down, please make

In Red

 

 

Turned

Lighting

confirmation of the following items, and then turn the power on again.

or

off

In Red

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy, please set FAN

 

 

 

SPEED of SERVICE item in OPTION menu to HIGH (￿59).

 

 

 

It is time to clean the air filter.

Lighting

Simultaneous

Please immediately turn the power off, and clean or

change the air filter referring to the section Cleaning

In Green

blinking in Red

and replacing the air filter. After cleaning or changing

 

 

 

the air filter, please be sure to reset the filter timer.

 

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

 

 

 

After the treatment, reset the power to ON.

 

 

 

 

Blinking In

 

 

At least 1 Power ON schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

Please refer to Schedule Settings section of User’s

seconds.

 

 

Manual - Network Guide.

NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Shutting the projector down

Shutdown switch

Only when the projector can not be turned off by usual procedure (￿18), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough.

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (￿63) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default.

98

Page 97 Page 99
Image 98
Page 97 Page 99
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Features Checking the contents of packagePart names ProjectorControl port Control panel and Lens adjustersRear panel 10 ~ LAN port Audio IN1 portComputer button Remote controlDown button Volume + button STANDBY/ON buttonCP-X4021N, CP-X5021N Setting upArrangement Screen Projection Screen height Size Distance CP-WX4021N1610 Projection Screen height DistanceDo not place the projector on a metal stand Connecting with your devices About Plug-and-Play capabilityConnecting with your devices ComputerStorage Computer Access pointUSB DeviceDigital VCR/DVD/Blu-ray Disc player Video Device Speakers Monitor Microphone Wired System Remote Control OptionalMicrophone function Power cord Connecting to a power supplyUsing the security bar and slot Anti-theft chain or wire Security bar Security slotAbout the remote control signal Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6 or R6PChanging the frequency of remote control signal Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the soundVideo button Press the MY Source / DOC. Camera button onComputer button MY SourceFor an Hdmi signal Searching an input signalFor a computer signal Selecting an aspect ratioAdjusting the projector’s elevator Horizontal Adjusting the lensFocus ring Zoom ring Lock Horizontal adjuster lock VerticalUsing the automatic adjustment feature Adjusting the positionCorrecting the distortion AutoPerfect FIT Using the magnify feature Magnify ON/OFF buttonFreeze button Temporarily freezing the screenTemporarily blanking the screen Blank buttonAdvanced Menu Using the menu functionEasy Menu Indication in OSD On Screen Display Indication MeaningAuto Keystone Picture ModeAspect KeystoneMirror ECO ModeReset Filter TimeContrast Picture menuBrightness GammaTint Color TempColor Active Iris SharpnessPresentation Theater OFF SAVE-1, SAVE-2, SAVE-3, SAVE-4Image menu For a computer signalFor an Hdmi signal Position USB Type B or Hdmi portSize PhaseAuto Adjust ExecuteHigh MID LOW Input menuTV Film OFF Video NRHdmi Range Video FormatHdmi Format Frame Lock Auto Sync on G OFFComputer On OFFResolution Setup menu Normal Hinvert Vinvert H&VINVERT Auto ECO ModeNormal ECO Normal Saving Speaker VolumeAudio menu Audio SourceMIC Level MIC VolumeHdmi Audio Blank Screen menuEnglish Français Deutsch Español Start UPMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Sync is OUT of Range MyScreen LockNo Input is Detected Invalid Scan FreqSource Name Template Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3Mode Description Closed CaptionDisplay ChannelAuto Search Direct PowerOption menu AutoUSB Type B Auto PowerOFF Air filter Cancel OKLamp Time MY Button Computer IN1 Computer IN2 LAN USB Type a Video S-VIDEO Component Hdmi USB Type BGhost ServiceFAN Speed Filter MessageRemote Freq Control Panel Remote ControlKEY Lock 1NORMAL 2HIGHBaud Rate Serial SettingsCommunication Type ParityStack Response Limit TimeTransmission Method Factory Reset InformationDynamic Host Configuration Protocol Setup DhcpNetwork menu IP Address DefaultSetup Gateway SubnetProjector Name MY Image AMX D.DQuit PresentationMulti PC User NameGuide Enter the Security menu PasswordSecurity menu SecurityMyScreen Turning on the MyScreen PasswordTurning off the MyScreen Password Turning off the PIN Lock PIN LockTurning on the PIN Lock If you have forgotten your PIN codeTurning off the Transition Detector Transition DetectorTurning on the Transition Detector Turning off the MY Text Password MY Text PasswordTurning on the MY Text Password Writing IndicatorMY Text Stack LockSupported storage media Presentation toolsPC-LESS Presentation Supported formatThumbnail mode Down Operating by buttons or keysButton operation Enter InputOperating by the menu on the Thumbnail screen This file seems to be broken or not supported format Full Screen Mode Slideshow mode Return Playlist USB Display Right-Click menu Options window Type number DT01171 Replacing the lamp MaintenanceReplacing the lamp High Voltage High Temperature High Pressure Lamp warningCleaning and replacing the air filter Type number MU06641 Filter unitCleaning and replacing the air filter Replacing the internal clock battery Maxell , part number CR2032 or CR2032HInside of the projector Caring for the cabinet and remote controlOther care Caring for the lensAn improper signal is input TroubleshootingThere is no input signal Related messagesInternal temperature is rising Button operation is not availableRegarding the indicator lamps Power Lamp TempShutting the projector down Resetting all settingsPower Lamp Temp indicator indicator indicator Description Signal source does not correctly work Phenomenon Cases not involving a machine defectAudio SOURCE/SPEAKER setting is not correct Signal cables are not correctly connectedVolume is adjusted to an extremely low level Brightness is adjusted to an extremely low levelFrame Lock function cannot work on the current Input signal Color settings are not correctly adjustedColor Space setting is not suitable Freeze function is workingCommunication Type for the Control port is Computer cannot start up in the current hardwareSaving function is working Set to Network BridgeSpecifications End User License Agreement for the Projector Software
Top Page Image Contents