Oki 7100e+ manual Pop-Up Conditions Display

Page 36

Pop-Up Conditions

Display

In this screen, you can set the conditions under which the Pop-Up Monitor pops up or is minimized to an icon.

If you check an item inside the Launch PopUp Monitor upon frame, the Pop-Up Monitor automatically pops up when the printer being monitored enters the state shown by the checked item.

If you check an item inside the Return to Icon, upon frame, the Pop-Up Monitor automatically becomes an icon when the printer being monitored enters the state shown by the checked item.

In this screen, you can set the following items relevant to the Pop-Up Monitor screen:

Add to Windows Startup Menu: If you check this item, the Pop-Up Monitor is registered in the Windows Start up Menu and starts each time Windows starts. If you clear it, the Pop- Up Monitor is deleted from the Windows Start up Menu.

If you check the item Save location of window, the monitor’s current position is saved and its dialog box opens in the same screen position each time that it is run.

36 Network print server

Image 36

Contents User’s Guide 59324102Network print server Contents Troubleshooting Specifications IndexNovell NetWare Introduction ComponentsNetwork print server Adapter CardHP JetAdmin and Web JetAdmin Support OKI Print Monitor UtilityNetwork print server Installation Network print server 100BASE-TX/10BASE-T Connector Network Print Server Part NamesStat Light red LED Link 100M Light green LED, center Link 10M Light green LED, near cableNetwork Print Server Configuration Setting Up the Network Print Server Using OkiviewOkiview 32 Printer Panel Okiview 32 Printer Properties MenuStatus Network PropertiesNovell Configuration Novell List PanelNovell Information Panel Changing the Printerís Name and LocationIP Address Setup Repeat for 84SUBNET Mask and 85DEFAULTPressMENU/EXIT Using the Network print server Web T p / / 1 9 3 3 2 Settings TCP/IP SettingsNetWare Settings Print Server ModeFile Servers per Pserver Mode NetBEUI SettingsEtherTalk Settings Connecting Using TCP/IP Snmp SettingsMIB-II Category Printer MenuUsing Telnet Connecting One Printer and One ComputerPrinter Address Subnet Mask Arp -s 192.168.20.127 0080920011BC tempSettings Main screen TCP/IP setup screen DHCP/BOOTP protocolRoot password Back to prior menu Please select 1 99? Snmp setup screenNetWare setup screen Packet type 802.3 NetWare modeNetWare print server mode setup screen Please select 1-99? Message Value NetWare protocolMessage Value Pserver name Job timeout Back to prior menu Please select 1-99? Message Value EtherTalk protocolZone Name Back to prior menu Please select 1 99? Resetting the fax machine Printer trap setup screenPlease select 1-99? Message Value Trap enable Trap typeWindows Printing OverviewAdd Printer Driver Network Print Server Setup for Windows Network print server User’s Guide English Network print server Add the LPR Port Network print server Pop-Up Monitor Task TrayPrinter Selection Monitor Screen Always display on topSetup Dialog Status MonitoringPop-Up Conditions Display User’s Guide English Print Server Mode Remote Printer ModeNovell NetWare IntroductionSetting up the Network Print Server Using Bindery PrintingClick Novell Novell Directory Services NDS Setting up the Network Print Server using OkiviewVerifying that the Printer is Connected Click Change Context Click OKClick Add/Delete Queue Click OK. Then Click OK in the Printer PropertiesNovell Distributed Print Services Ndps Setting up the ClientsAdd Printer Wizard will start Troubleshooting Fax machine cannot find the network print serverFax machine does not print via lpr or ftp Problems printing via NetWare User name in bannerFax machine does not print Problems printing self diagnostics test and configuration If the ROM check or RAM check result is NG no goodIf the Eeprom check result is NG If NIC Check is marked with NGNetwork print server Status Lights Specifications Network InterfaceNetwork Protocol FunctionsIndex Network print server