Xerox manual After installation, Model 2750 Folder operator’s side, Power entry panel

Page 14

Chapter 2

OPERATING INSTRUCTIONS

After installation ...

Your Printfold installer will have demonstrated how the folder operates with your printer or copier, showing how the bridge can be pivoted vertically for access to the rear of the printing system, and also how, in the event of a folder jam, documents are diverted to avoid a build-up of paper at the printer exit.

Model 2750 Folder (operator’s side)

Features to note ... The bridge, shown here locked down in the operating position, so that documents exiting the printer/copier flow into the bridge; the tower (raised section at center) which passes unfolded documents from the bridge to the stacking surface formed by the folder lids; the operator’s control panel (upper surface of tower), with push-buttons and LEDs; the removable catch-bin which receives folded packets from the crossfolder, and; the rear receiving tray for accordion folded documents exiting the folder without crossfolding (not shown in photo).

The Printfold Model 2750 Folder is self-programming, and so automatic in operation that there is really very little for the operator to do. The folder turns on automatically when a document enters the bridge, and turns off (times-out), when the flow of prints ceases. There is no need to figure the fold pattern for each document, nor is it necessary to remember which fold types and sizes are possible with a given width of media. All you have to do, as the operator, is select the desired style of fold from the control panel, and empty the catch bin from time to time.

For an overview of the folder the user is referred to Chapter 1, which introduces the various fold possibilities and illustrates the folder’s key features.

4

0 0 0 3 1 9

Power entry panel

3

2

1

5

6

(1)Power entry module

(2)Line cord receptacle (IEC-320)

(3)ON/OFF rocker switch: 1 = ON, 0 = OFF

(4)Fuse drawer (3AG type)

(5)Linear Feet counter

(6)Communications port (DB9-F)

2750 op#2 R3.doc 10-02

Page 2-1

Image 14

Contents PRINTFOLD Synergix Fold System Engineering Document Folder Main components of the Model 2750 Folder General informationSynergix Fold System Power entry module / counter / communications port Operator’s control panelMain control panel Stacker/Handfeed Instant service accessBridge Automatic document diversionTower in normal folding and bypass modes Manual feed slotAccordion folding overview Standard accordion fold packetType F bookfold packet Crossfolding overview Folds handle easier than Z-foldsLEL = non-standard feed direction Key facts about fold programsSEL = standard feed direction Width sensors at input end of bridge Main features of the 2750 folding system Options availableModel 2750 Folder operator’s side After installationPower entry panel 12 Z-folded packet, portrait style Operator’s controls½ x 11 C-folded packet, landscape style BkaZ ½ x 11 book-folded packet Z fold onlyFold Selection Host controller Start-upOn-line programs Reset procedureFold Selection Standalone Hand feed programsManual document feeding Rear of diverter tower, showing stacker/off-line componentsTo begin hand feeding Hand feeding a documentExiting Handfeed Mode Jam conditions Clearing a jamRaising the bridge lid Bridge and Bridge ExitIf the document is visible Unlocking the bridgeRaising the bridge Access to the towerTower Accordion folder lid in raised position Use the jog feature …Accordion Folder Opening the upper clam shellEjector springs on crank handle Using the crank handle to rotate the drumRaising the drum faceplate shutter Upper section of the crossfolder in raised position CrossfolderCrossfolder latches Crossfolder rear panel Crossfold TransferCrossfold Pocket and Crossfold Exit Unhitching the accordion and cross folderCrossfold pocket Interlock OpenCrank handle engaged in crossfold roll System Error In-feed and accordion folding components Initial phase of the folding programAccordion Folder Completion of the first fold Panel measuring phaseDrum reversal develops a loop Starting the second fold Accordion fold compensating panelsFirst crossfold action Document inversionCrossfolder Single crossfold mode Double crossfold modeOperator’s control panel System MenuJog functions PasswordsCommunications mode Parameter viewing and modificationAccessible only to the Key Operator and technician Device testSheets 1s 3 0 5 Recent errorsActivity counters 721p Synergix Fold System 40 & XES 2750 Series fold tables DescriptionAfnor Fold Banks Peco Fold MIXFold Bank 1 common European sizes Folder Error Messages Message Definition Location or type of error