Xerox 2750 manual Operator’s control panel, System Menu

Page 35

Chapter 4

System Menu and Key Operator Functions

Operator’s control panel

The operator’s control panel displays which fold tables the folder is currently configured to perform and also will display an error code in the event of an error. There are also many diagnostic tools available from the control panel. The last item always displayed along with the operator selectable folds is called the System Menu.

When the display reads ONLINE, press any of the keys directly below the display to access the

System Menu.

When selecting System Menu, 9 additional choices are available:

Communications – Sets the communications port mode: 1 = on line (folder accepts fold commands from the host controller); 2 = use keypad (folder overrides commands from elsewhere); 3 = none (comms port disabled); 4 = loop back test (used to test the comms port). Selecting 3 or 4 on a Max 200 system will result in the need to cycle power on the Max 200.

Infeed Jog Fwd (forward) – Drives the accordion infeed motor forward about ½ revolution to assist in clearing infeed jams.*

Infeed Jog Rev (reverse) – Reverses the accordion infeed motor about ½ revolution to assist in clearing infeed jams.*

Parameters – Displays the operating parameters of the folder. Changes can only be made by a technician entering the appropriate password.

Device Test – Allows the Key Operator the ability to energize all of the solenoids and some of the motors for diagnostics. Up to two items can be energized for up to 15 seconds before the folder automatically shuts that item off, except for motors, which won’t automatically be shut off. WARNING: Repeated on cycles of certain solenoids without allowing for cooling time may lead to failure of the solenoid and/or the circuit board. This setting is only available when the Key Operator password is active.

Assign Folds – Assigns a fold table from the master fold table list to a location on the keypad for the operator to access for online folding. Changes can only be made if the Key Operator password is active.

Assign Handfeeds – Assigns a fold table from the master fold table list to a location on the keypad for the operator to access for offline folding (hand feeding). This list is limited as not all fold tables are available when hand feeding. Changes can only be made if the Key Operator password is active.

Recent Errors – Displays the error codes of the last 21 errors recorded, with an indication of how many prints had successfully been processed by the folder between errors. The list can be cleared if the keypad password is active.

Stack Sensor – Displays the state of stack exit sensor, 0 = blocked and 1 = clear. Quit – Returns the display back to the operator fold selections or ONLINE.

* Jog functions are only available when the error light is on and the interlocked doors are closed.

2750 op#4 R3.doc 10-02

Page 4-1

Page 34 Page 36
Image 35
Page 34 Page 36
Contents PRINTFOLD Synergix Fold System Engineering Document Folder Main components of the Model 2750 Folder General informationSynergix Fold System Operator’s control panel Power entry module / counter / communications portMain control panel Automatic document diversion Instant service accessBridge Stacker/HandfeedManual feed slot Tower in normal folding and bypass modesStandard accordion fold packet Accordion folding overviewType F bookfold packet Folds handle easier than Z-folds Crossfolding overviewLEL = non-standard feed direction Key facts about fold programsSEL = standard feed direction Width sensors at input end of bridge Options available Main features of the 2750 folding systemModel 2750 Folder operator’s side After installationPower entry panel BkaZ ½ x 11 book-folded packet Z fold only Operator’s controls½ x 11 C-folded packet, landscape style 12 Z-folded packet, portrait styleStart-up Fold Selection Host controllerHand feed programs Reset procedureFold Selection Standalone On-line programsRear of diverter tower, showing stacker/off-line components Manual document feedingHand feeding a document To begin hand feedingExiting Handfeed Mode Clearing a jam Jam conditionsUnlocking the bridge Bridge and Bridge ExitIf the document is visible Raising the bridge lidRaising the bridge Access to the towerTower Opening the upper clam shell Use the jog feature …Accordion Folder Accordion folder lid in raised positionEjector springs on crank handle Using the crank handle to rotate the drumRaising the drum faceplate shutter Upper section of the crossfolder in raised position CrossfolderCrossfolder latches Unhitching the accordion and cross folder Crossfold TransferCrossfold Pocket and Crossfold Exit Crossfolder rear panelCrossfold pocket Interlock OpenCrank handle engaged in crossfold roll System Error In-feed and accordion folding components Initial phase of the folding programAccordion Folder Completion of the first fold Panel measuring phaseDrum reversal develops a loop Accordion fold compensating panels Starting the second foldFirst crossfold action Document inversionCrossfolder Double crossfold mode Single crossfold modeSystem Menu Operator’s control panelParameter viewing and modification PasswordsCommunications mode Jog functionsDevice test Accessible only to the Key Operator and technicianSheets 1s 3 0 5 Recent errorsActivity counters Description 721p Synergix Fold System 40 & XES 2750 Series fold tablesAfnor Peco Fold MIX Fold BanksFold Bank 1 common European sizes Message Definition Location or type of error Folder Error Messages
Top Page Image Contents