Xerox 2750 manual Fold Selection Standalone, Reset procedure, On-line programs, Hand feed programs

Page 17

The communications protocol in effect is determined by the firmware installed in the folder, and by the Host parameter in the Parameters menu.

USE KEYPAD FOLDS mode – integrated system

In this mode the control panel on the folder is used to select the fold program, overriding fold selections made elsewhere. All other communications features remain in effect, including shutdown and job recovery functions, and sheet size transmission.

In the USE KEYPAD FOLDS mode, the control panel displays up to four fold choices, the current selection being marked with an asterisk (in the diagram above: *8.5 x 11 LAND C = an 8½” x 11” packet, landscape format, with C-style crossfold). The fold choices are factory-assigned to specific fold banks from a set of over 100 programs resident in the 2750 firmware (fold bank examples: 0 = USA, 1 = DIN, 3 = France). Fold banks may be edited on-site at any time by trained service technicians.

To change the fold program selection press the button number indicated on the display. If the desired program is not visible, press the +> button as necessary to scroll through the list. If the operator selects something other than the fold display mode, password protection ensures that the folder settings cannot be altered inadvertently.

On-line programs

Page 1

1:STACK

2:

8.5x11

LAND C

3:

8.5x11

PORT C

4:

9x12

LAND C

Page 2

 

1:

9x12

PORT C

2:

8.5x11

BkF1.00

3:

8.5x11

BkB1.00

4:

8.5x11

MIXED C

Page 3

 

1:

9x12

MIXED C

2:

8.5

FANFOLD

3:

7080/85

8.5x11

4:System Menu

Hand feed programs

Page 1

 

1:

8.5x11

LAND C

2:

8.5x11

PORT C

3:

9x12

LAND C

4:

9x12

PORT C

Page 2

 

1:

8.5

FANFOLD

2:

9.0

FANFOLD

3:11.0 FANFOLD

4:12.0 FANFOLD

Page 3

1:System Menu

NOTE: Hand feed prints face down, with title block leading

NONE mode – communications inoperative

The NONE mode applies to stand-alone folders, or to integrated systems in which the serial connection to the folder is not functioning. Fold program selection is identical to that described above in USE KEYPAD FOLDS.

Fold Selection – Standalone

When the folder is not connected to a host, the fold selection is made through the folder control panel with an asterisk (in the diagram above: *8.5 x 11 LAND C = an 8½” x 11” packet, landscape format, with C-style crossfold).

Reset procedure

The 2750 folder automatically resets itself once a jam or other fault condition has been corrected, and the covers have all been replaced to complete the interlock circuit. When the last cover is replaced you will hear the sound of motors and rollers running, provided a fault condition is no longer present, in which case the control panel will indicate the fault location.

2750 op#2 R3.doc 10-02

Page 2-4

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PRINTFOLD Synergix Fold System Engineering Document Folder Main components of the Model 2750 Folder General informationSynergix Fold System Operator’s control panel Power entry module / counter / communications portMain control panel Bridge Instant service accessStacker/Handfeed Automatic document diversionManual feed slot Tower in normal folding and bypass modesStandard accordion fold packet Accordion folding overviewType F bookfold packet Folds handle easier than Z-folds Crossfolding overviewLEL = non-standard feed direction Key facts about fold programsSEL = standard feed direction Width sensors at input end of bridge Options available Main features of the 2750 folding systemModel 2750 Folder operator’s side After installationPower entry panel ½ x 11 C-folded packet, landscape style Operator’s controls12 Z-folded packet, portrait style BkaZ ½ x 11 book-folded packet Z fold onlyStart-up Fold Selection Host controllerFold Selection Standalone Reset procedureOn-line programs Hand feed programsRear of diverter tower, showing stacker/off-line components Manual document feedingHand feeding a document To begin hand feedingExiting Handfeed Mode Clearing a jam Jam conditionsIf the document is visible Bridge and Bridge ExitRaising the bridge lid Unlocking the bridgeRaising the bridge Access to the towerTower Accordion Folder Use the jog feature …Accordion folder lid in raised position Opening the upper clam shellEjector springs on crank handle Using the crank handle to rotate the drumRaising the drum faceplate shutter Upper section of the crossfolder in raised position CrossfolderCrossfolder latches Crossfold Pocket and Crossfold Exit Crossfold TransferCrossfolder rear panel Unhitching the accordion and cross folderCrossfold pocket Interlock OpenCrank handle engaged in crossfold roll System Error In-feed and accordion folding components Initial phase of the folding programAccordion Folder Completion of the first fold Panel measuring phaseDrum reversal develops a loop Accordion fold compensating panels Starting the second foldFirst crossfold action Document inversionCrossfolder Double crossfold mode Single crossfold modeSystem Menu Operator’s control panelCommunications mode PasswordsJog functions Parameter viewing and modificationDevice test Accessible only to the Key Operator and technicianSheets 1s 3 0 5 Recent errorsActivity counters Description 721p Synergix Fold System 40 & XES 2750 Series fold tablesAfnor Peco Fold MIX Fold BanksFold Bank 1 common European sizes Message Definition Location or type of error Folder Error Messages
Top Page Image Contents