Xerox 2750 Operator’s controls, ½ x 11 C-folded packet, landscape style, Operators Control Panel

Page 15

Handfeed

Pressing the Handfeed push- button switches the 2750 into hand-folding mode, displaying a modified list of programs. The print to be folded is fed into the rollers at the rear of the folder (image face-down, title block leading - centering is not important, but alignment is).

Folder ON

Models 2753, 2755 and 2757

have similar control panels, with plain language in place of icons, e.g., MORE in place of +>

Receiver Advance Advances conveyor belts on High Capacity Print Receiver, if installed

Indicates a fault/jam condition, or open cover

Operator's Control Panel

Synergix Fold System 40

Operator’s controls

The push-buttons on the operator’s control panel are “soft-programmed”, which means they are used for a number of tasks including selection of the fold program to be applied to incoming prints. The folder firmware includes over 50 fold programs (“tables”), up to 20 of which may be quickly accessed by the operator using the push-buttons. (The fold programs are listed in Chapter 4, and also in the Fold Directory. A separate set of up to 20 programs for hand feeding is also provided.

In most cases the folder is connected to a host controller through its serial interface and when the folder is powered up the display will read ONLINE. If the folder is not connected to a host or the Communications mode is not set to “Normal” the control panel displays the first four fold programs selected for your folder, as in the example below:

1:8.5 x 11 PORT C 8½” x 11” C-folded packet, portrait style

2: *

8.5 x 11

LAND C

8½” x 11” C-folded packet, landscape style

3:

9 x 12

PORT Z

9” x 12” Z-folded packet, portrait style

4:

8.5 x 11

BkaZ

8½” x 11” book-folded packet (Z fold only)

In this sample display, fold program #2 is active, which means the folder will fold every incoming print (other than A-size sheets) into 8½” x 11” landscape packets.

If more than four fold programs have been selected for your installation, press the MORE button to display.

2750 op#2 R3.doc 10-02

Page 2-2

Image 15
Contents PRINTFOLD Synergix Fold System Engineering Document Folder General information Synergix Fold SystemMain components of the Model 2750 Folder Operator’s control panel Power entry module / counter / communications portMain control panel Automatic document diversion Instant service accessBridge Stacker/HandfeedManual feed slot Tower in normal folding and bypass modesStandard accordion fold packet Accordion folding overviewType F bookfold packet Folds handle easier than Z-folds Crossfolding overviewKey facts about fold programs SEL = standard feed directionLEL = non-standard feed direction Width sensors at input end of bridge Options available Main features of the 2750 folding systemAfter installation Power entry panelModel 2750 Folder operator’s side BkaZ ½ x 11 book-folded packet Z fold only Operator’s controls½ x 11 C-folded packet, landscape style 12 Z-folded packet, portrait styleStart-up Fold Selection Host controllerHand feed programs Reset procedureFold Selection Standalone On-line programsRear of diverter tower, showing stacker/off-line components Manual document feedingHand feeding a document To begin hand feedingExiting Handfeed Mode Clearing a jam Jam conditionsUnlocking the bridge Bridge and Bridge ExitIf the document is visible Raising the bridge lidAccess to the tower TowerRaising the bridge Opening the upper clam shell Use the jog feature …Accordion Folder Accordion folder lid in raised positionUsing the crank handle to rotate the drum Raising the drum faceplate shutterEjector springs on crank handle Crossfolder Crossfolder latchesUpper section of the crossfolder in raised position Unhitching the accordion and cross folder Crossfold TransferCrossfold Pocket and Crossfold Exit Crossfolder rear panelInterlock Open Crank handle engaged in crossfold rollCrossfold pocket System Error Initial phase of the folding program Accordion FolderIn-feed and accordion folding components Panel measuring phase Drum reversal develops a loopCompletion of the first fold Accordion fold compensating panels Starting the second foldDocument inversion CrossfolderFirst crossfold action Double crossfold mode Single crossfold modeSystem Menu Operator’s control panelParameter viewing and modification PasswordsCommunications mode Jog functionsDevice test Accessible only to the Key Operator and technicianRecent errors Activity countersSheets 1s 3 0 5 Description 721p Synergix Fold System 40 & XES 2750 Series fold tablesAfnor Peco Fold MIX Fold BanksFold Bank 1 common European sizes Message Definition Location or type of error Folder Error Messages