Xerox 2750 manual To begin hand feeding, Hand feeding a document

Page 19

HAND	HANDFEED light off - hand feed program not initiated
FEED

HAND HANDFEED light on steady - folder is ready to accept a print

FEED

HAND	HANDFEED light flashes - folder is currently folding a print
FEED

To begin hand feeding ...

1.If applicable to your system, check the printer controller/host computer to make sure no prints are queued to the folder.

2.Press the HANDFEED button. If a fold is in process or a sheet coming command has been set by the controller an audible beep will sound and the HANDFEED button must be pressed again when the system is clear. At this point the LED is a steady green and the folder is ready for hand feeding.

3.On the operator’s control panel, press the appropriate push-button to select the desired packet size and style.

4.Slide the accessory plate back from the infeed slot.

5.Turn the document face down, positioned so that the title block is nearest to the infeed slot.

6.Keeping the document square to the infeed rollers, slide it gently forward until the infeed sensor energizes the drive system.

During the folding process, the HANDFEED green LED on the operator’s control panel flashes, indicating that the system is busy. Do not try to hand feed another document until the light stops flashing.

Hand feeding a document

Center the document in the infeed slot, then feed it slowly forward until engaged by the rollers.

2750 op#2 R3.doc 10-02

Page 2-6

Image 19

Contents PRINTFOLD Synergix Fold System Engineering Document Folder Synergix Fold System General informationMain components of the Model 2750 Folder Operator’s control panel Power entry module / counter / communications portMain control panel Automatic document diversion Instant service accessBridge Stacker/HandfeedManual feed slot Tower in normal folding and bypass modesStandard accordion fold packet Accordion folding overviewType F bookfold packet Folds handle easier than Z-folds Crossfolding overviewSEL = standard feed direction Key facts about fold programsLEL = non-standard feed direction Width sensors at input end of bridge Options available Main features of the 2750 folding systemPower entry panel After installationModel 2750 Folder operator’s side BkaZ ½ x 11 book-folded packet Z fold only Operator’s controls½ x 11 C-folded packet, landscape style 12 Z-folded packet, portrait styleStart-up Fold Selection Host controllerHand feed programs Reset procedureFold Selection Standalone On-line programsRear of diverter tower, showing stacker/off-line components Manual document feedingHand feeding a document To begin hand feedingExiting Handfeed Mode Clearing a jam Jam conditionsUnlocking the bridge Bridge and Bridge ExitIf the document is visible Raising the bridge lidTower Access to the towerRaising the bridge Opening the upper clam shell Use the jog feature …Accordion Folder Accordion folder lid in raised positionRaising the drum faceplate shutter Using the crank handle to rotate the drumEjector springs on crank handle Crossfolder latches CrossfolderUpper section of the crossfolder in raised position Unhitching the accordion and cross folder Crossfold TransferCrossfold Pocket and Crossfold Exit Crossfolder rear panelCrank handle engaged in crossfold roll Interlock OpenCrossfold pocket System Error Accordion Folder Initial phase of the folding programIn-feed and accordion folding components Drum reversal develops a loop Panel measuring phaseCompletion of the first fold Accordion fold compensating panels Starting the second foldCrossfolder Document inversionFirst crossfold action Double crossfold mode Single crossfold modeSystem Menu Operator’s control panelParameter viewing and modification PasswordsCommunications mode Jog functionsDevice test Accessible only to the Key Operator and technicianActivity counters Recent errorsSheets 1s 3 0 5 Description 721p Synergix Fold System 40 & XES 2750 Series fold tablesAfnor Peco Fold MIX Fold BanksFold Bank 1 common European sizes Message Definition Location or type of error Folder Error Messages