Xantrex Technology RS232-XHR manual Cmode

Page 45

	Operation
	Command Summary
Table 3.5	Calibration Commands
Command	Description

CMODE	Places the supply into calibration mode.

IDATA	Calculates the slope and intercept for current programming.

IHI	Sets the current output to the high calibration point.

ILO	Sets the current output to the low calibration point.

IRDAT	Calculates the slope and intercept for current readback.

IRHI	Sets the current output to the high readback point.

IRLO	Sets the current output to the low readback point.

OVCAL	Calibrates the over voltage protection (OVP).

VDATA	Calculates the slope and intercept for voltage programming.

VHI	Sets the voltage output to the high calibration point.

VLO	Sets the voltage output to the low calibration point.

VRDAT	Calculates the slope and intercept for voltage readback.

VRHI	Sets the voltage output to the high readback point.

VRLO	Sets the voltage output to the low readback point.

Table 3.6	Status Commands
Command	Description

ASTS?	Asks for the supply’s accumulated status register.

FAULT?	Asks for the supply’s fault register for the status preset operating
	conditions.
MASK	Prevents the supply's previously unmasked operating conditions from
	setting bits in the fault register.
STS?	Asks for the supply’s present status register.

UNMASK	Enables you to select those supply's operating conditions that you are
	most interested in monitoring for fault occurrence.
UNMASK?	Asks for the supply's fault conditions which are currently enabled
	(unmasked).

Release 3.1

43

Image 45

Contents RS232-XHR RS232-XFR Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service?What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplySupply SafetyManual Revisions Main SectionsAbout This Manual Contents Calibration Description Features and SpecificationsFeatures Features and FunctionsFeatures and Specifications Readback FunctionsModels 140 12-100 20-60 35-35 40-30 SpecificationsModels 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Initial Inspection IntroductionInitial Inspection Installation and ConfigurationRS-232 Interface Subplate Located on Power Supply Rear Panel RS-232 Interface PCB Step # Description Action Reference Basic Setup ProcedureFlow Switch Setting Condition CommunicationsBaud Rate Jumper Connections RS-232 Connector Pin XON Switch Setting ConditionJumper J216 Connections RS-232 Connector Pin Power Supply DCE Host Computer DTE Pin connectorSwitch Position Power on results RemoteStartup Iset Condition Default Settings Model ExampleExample Command RS-232 ConnectionLocal Lockout Parameter Setting Power Supply Settings12 OVP Control Mode Selection User Options and SettingsHigh OFF LOW User Signals J7 Connector User SignalsJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block RS-232 Operation Command SyntaxFormat OperationFloating Number Definition Example Parameter Description FormOperation Command Description Command SummaryAUXA? Cmode Auxa 1 on Command ReferenceResponse DLY seconds Lockout. See also Remote/Local Operation on Snsp Remote/Local Operation on Status, and Fault Registers on Section Accumulated Status, Status, and Fault Registers 4096 Condition Mnemonic Bit Position Bit WeightError # Error Identification Explanation Error CodesLEDs TroubleshootingCalibration Setup Voltage Mode CalibrationVoltage Program Calibration Procedure VoltageVoltage Readback Calibration Procedure Current Mode Calibration Current Calibration SetupCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc