Fujitsu fi-4750L manual

Page 63

Reading Mode Setting When the Video Interface Option is Installed

This section describes the button specifications and setup details for each of the simplex (front-side), duplex (front-side) and duplex (back-side) reading modes when the scanner has the video interface option in the third party slot.

When the reading mode is set by the command from the host computer, the following button operation is not required.

NOTICE

When the video interface option is installed in the scanner, the scanner automatically recognizes the board and changes the display.

Whenever you press , the scanner returns to screen M1. <Screen M1>

1Turn the power On and verify that “Scanner

Ready” is displayed on the LCD.

<Screen M2>

2Press then the scanner displays Screen M2.

3Press then the scanner displays Screen 1.

<Screen 1>

4Select ADF or FB by pressing or then

press . The scanner displays Screen 2.

<Screen 2>

5 Select “Simplex” or “Duplex” by pressing or . Then press Enter. The scanner displays Screen 3.

<Screen 2>

6Select “Portrait” or “Landscape” by pressing

or . Then press . The scanner displays Screen 4.

<Screen 4>

7Select Size by pressing or . Then press . The scanner displays Screen 5.

<Screen 5>

8Select Resolution by pressing or . As

the cursor moves to the left 100/150 may

appear. Then press . The scanner displays Screen 6.

6-4

Image 63
Contents Fi-4750L Image Scanner Fi-4750L Image Scanner Revisions, Disclaimers Page Fujitsu France S.A Fujitsu OfficesPage Preface Conventions Contents Viii Terms Index Checking the Components Units and Assemblies Operator Panel ComponentsChecking the Components Units and Assemblies UnitsFi-4750L Function Assemblies Arrangement Operator PanelName of the button Function Button/LED FunctionCounter Function Counter DisplayOperation status Temporary error Alarm Page Page Installation and Connections Precautions Inspection Repositioning the Shipping Lock Turning the power switch Off Connecting the power cableCable Connections Connecting the chute cable Connecting the interface cablesMounting the Stacker Setting the Scsi ID and the Scsi Terminator Page Operating Instruction Turning the Power On Waking up the Scanner from the Low Power Mode Manual Feed Mode Setting ADF Loading Documents on the ADFABD Documents Guide Guide lever Both sides Max 20 mm 0.8 or 10 mm 0.4 See Notices Loading Documents on the Flatbed Scanner parts involved when loading documentsReading a Page from a Thick Book Page ADF Document Specification Document Size Scanner Maximum MinimumFi-4750L A3/Double Letter A8 Portrait Document type Paper weightPrecautions Document QualityMore than 30 mm Less than Feed direction Top of the paper Country Unit Conversion ADF Document Feeder CapacityAreas that must not be perforated Areas not to be PerforatedGrounding color area Grounding Color AreasDouble Feed Detection Condition Job separation sheet Job Separation SheetScanner Specifications Specification Remarks Basic Product SpecificationSpecification Installation SpecificationDimensions Page Consumables Options Video Interface Option IPC-4D Option Consumables and OptionsConsumables Name Specification RemarksName Remarks OptionsVideo Interface Option How to Install the Video Interface Option BoardPage Parameter Description Without IPC With IPC-4D Description OptionParameter Description IPC-4D Option Page Activating the Setup Mode Contents of the Setup Mode Setup ModeActivating the Setup Mode Contents of the Setup Mode Scsi ID Setting double feed detection Paper Thickness Setting double feed detection Paper Length Setting IPC pre-set mode Setting the pick start time Reset of the abrasion counterSetting the time-out limit Page Scsi ID Setting Scsi Terminator SettingIPC Status Display Low Power Mode Setting Select Interface M4097D Display the TPS Board ID NumberSelect Built-In/IPC-4D Image Processing Image ProcessingAdjust ADF Erasing Edges Adjust FB Erasing Edges Page Glossary of Terms Double Letter Size IPC-4D Paper JAM TPS GL-6 Index Pick start time Declarations of Conformity DE-2