Fujitsu Siemens Computers X103 SFF manual Ports provided by the device, Disconnecting cables

Page 20

Disconnecting cables

Turn off all power and equipment switches.

Remove all power plugs from the grounded mains outlets.

Unplug all data communication cables from the utility sockets.

Unplug all cables from the device and peripherals.

i

USB devices are hot-pluggable. This means you can connect and disconnect devices

while your operating system is running.

Additional information can be found in the "Connecting external devices to the USB ports" section and in the documentation for the USB devices.

Ports provided by the device

The connections are located on the front and back of the device. The ports available on your device depend on the configuration level you have selected. The standard ports are marked with the symbols shown below (or similar). Detailed information on the location of the connections is provided in the manual for the mainboard.

 

 

 

 

 

 

 

 

 

Keyboard port, purple

PS/2 mouse port, green

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

1

 

 

 

 

 

 

 

 

 

 

Serial port 1, teal or turquoise

Serial port 2, teal or turquoise

 

 

 

 

 

 

 

 

 

Monitor port, blue

Parallel port/Printer, burgundy

 

 

 

 

 

 

 

 

 

Headphones port, orange or light

Microphone connector, pink (optional)

 

 

 

 

 

 

 

 

 

green (optional)

 

 

 

 

 

 

 

 

 

 

Audio output (Line out), light green

Audio input (Line in), light blue

 

 

 

 

 

 

 

 

 

Game port, gold

SCSI connection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USB - Universal Serial Bus, black

LAN LAN port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVI interface (optional)

Firewire (optional)

 

 

 

 

 

 

 

 

 

 

 

 

i

 

 

 

 

 

 

Some of the connected devices require special drivers (see the documentation for the

 

 

 

 

 

 

 

 

connected device).

 

12

VFY-SCED103S, edition 1

Image 20
Contents Edition X103 SFF Are there Page Published by Edition X103 SFF Operating ManualPage Contents Contents Your Edition X103 SFF Notational conventionsPage Safety notes Cleaning the deviceImportant notes Transporting the deviceCE marking for devices without radio component Energy saving, disposal and recyclingCE marking Steps for initial setup Preparing for useUnpacking and checking the delivery External devicesSetting up the device Vertical operating position Connect the monitor, mouse and keyboard Horizontal operating position with rubber feetConnecting a keyboard Connecting the monitorConnecting the mouse Connecting the device to the mains voltage Initial switch-on Software will be installedConnecting external devices Switching on monitor and deviceInstalling the software Connecting cablesDisconnecting cables Ports provided by the deviceConnecting external devices to the parallel or serial port Connecting external devices to the USB portsPort settings Device driversPage Operation Switching the device onSwitching off the device Indicators provided by the device Drive indicator, e.g. DVDFloppy disk indicator Hard disk indicatorON/OFF switch optional KeyboardImportant keys and key combinations Enter keyWarm boot Menu keyShift key Alt Gr e.g. German keyboardSettings in Bios Setup Working with floppy disksPage Troubleshooting and tips Installing new softwareMains voltage supply is faulty Internal power supply overloadedDevice cannot be switched off with the ON/OFF switch Screen stays blankNo mouse pointer displayed on the screen Floppy disk cannot be read or writtenWrong monitor has been set under Window XP Wrong RAM modules have been insertedError messages on the screen Restoring the hard disk contentsTime and/or date is not correct TipsSystem expansions Information about boardsClosing the casing Opening and closing the casingOpening the casing Installing a board Assembling and dismantling low-profile unitsRemoving the holding plate Removing a boardInserting and removing the drive cage Removing the drive cageRemoving the cross-piece Removing the front panelAttaching the drive cage Installing the drive cageDisconnecting cables Removing the drive cage System expansions IDE drives and serial ATA drives Installing and removing drivesInstalling the cross-piece Removing and installing accessible drives Installing and removing the hard diskSystem expansions Replacing lithium battery Extensions to the mainboardMaking changes on mainboard Upgrading main memoryFollowing changes Page Technical data DimensionsWeight Electrical dataPage Data IndexCable Index Scsi