Cisco Systems uBR7200 Series manual Enhanced Show Interface Upstream Output

Page 30

Chapter 4 Troubleshooting the System

Understanding Show Command Responses

Table 4-18 Show Interface Cable Upstream Command Field Descriptions (continued)

Field

Description

Avg percent minislots lost on

Indicates on average what percent of slots are lost because

late MAPs

a MAP interrupt was too late

 

 

Current minislot count

Indicates the current minislot count at the CMTS. FLAG

(formerly: Last Minislot Stamp

indicates the timebase reference. This field is used only by

(current_time_base))

developers.

 

 

Scheduled minislot count

Indicates the furthest minislot count allocated at the

(formerly: Last Minislot Stamp

indicated time. FLAG indicates the timebase reference.

(scheduler_time_base))

This field is used only by developers.

 

 

Enhanced Show Interface Upstream Output

The show interface cable upstream command is enhanced in Cisco IOS Release 12.0(7)XR2, Cisco IOS Release 12.1(1a)T1, or higher CMTS images to display detailed MAC scheduler state information for the upstream port. The example below illustrates the new display:

cmts#show interface cable 3/0 upstream 0 Cable3/0:Upstream 0 is up

Received 13 broadcasts, 0 multicasts, 110 unicasts 0 discards, 106 errors, 0 unknown protocol

123 packets input, 0 uncorrectable

106 noise, 0 microreflections

Total Modems On This Upstream Channel :3 (3 active)

Default MAC scheduler

 

Queue[Rng Polls]

0/20, fifo queueing, 0 drops

Queue[Cont Mslots]

0/104, fifo queueing, 0 drops

Queue[CIR Grants]

0/20, fair queueing, 0 drops

Queue[BE Grants]

0/30, fair queueing, 0 drops

Queue[Grant Shpr]

0/30, calendar queueing, 0 drops

Reserved slot table currently has 2 CBR entries

Req IEs 280185, Req/Data IEs 0

 

Init Mtn IEs 800, Stn Mtn IEs 49

 

Long Grant IEs 26, Short Grant IEs 15

 

Avg upstream channel utilization :1%

 

Avg percent contention slots :97%

 

Avg percent initial ranging slots :1%

 

Avg percent minislots lost on late MAPs :0%

Total channel bw reserved 192000 bps

 

CIR admission control not enforced

 

Current minislot count :1165412

Flag:1

Scheduled minislot count :1176227

Flag:1

New items in the display include:

Detailed slot queue statistics---Queue [CIR Grants] 0/20, fair queueing, 0 drops in the example above means that the queue for CIR-service grants has a current depth of 0, a maximum depth of 20. Weighted fair queueing shows grants in this queue.

CBR slot scheduling table state---The above reserved slot table has 2 CBR entries. This shows that at the time the command was issued, the MAC scheduler had admitted 2 CBR slots in the reserved slot table.

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

4-30

78-5897-01

 

 

Image 30
Contents Troubleshooting the System Configure Sync Message Interval Managing Cable Modems on the HFC NetworkActivate Cable Modem Upstream Address Verification Activate Cable Modem AuthenticationVerify Cable Modem Authentication Verify Sync Message IntervalCMTS01config-if#cable source-verify dhcp CMTS01config-if#no cable source-verifyVerify Cable Modem Upstream Address Verification CMTS01config-if#cable insertion-interval CMTS01config-if#no cable insertion-intervalCMTS01config-if#cable insertion-interval max AutomaticConfigure Per Modem Filters Configure access lists to be specified on a Configure Cable Modem Registration Timeout Clear Cable Modem ResetCMTS01config-if#cable registration-timeout n Verify Clear Cable Modem Reset Clear Cable Modem CountersConfigure Upstream Rate Limiting and Shaping Configure Traffic ShapingConfigure Downstream Rate Limiting and Shaping Verify Clear Cable Modem CountersToken-bucket CMTS01config-if#nocable upstream n1 rate-limitBlind Strategies and Time Scheduled Combined CMTS01# show interface c3/0 sid 1 countersGuided Frequency Hop Sample output Field DescriptionSpectrum Management Debug and Test Commands Show Cable Hop Command14 Show Cable Hop Parameter Descriptions Debug and Test Commands Polling Cable ModemsAllows you to configure access Enable SnmpConfigure Remote Modem Monitoring Verifying Remote Query InformationUnderstanding Show Command Responses General Show CommandsMonitoring and Maintaining Remote Querying Show Cable Modem See the sample command output below Page SID Show Cable Modem Maintenance Cable modem cable 3/0 upstream 0 unregisteredCable modem cable 3/0 upstream 0 offline UBR7200#show cable modem maintenance Show Interface CableMTU CRC Field Description Router# show interface cable 6/0 downstream18 Show Interface Cable Upstream Command Field Descriptions ATP Enhanced Show Interface Upstream Output Show Interface Cable SID Cable slot 3, portRouter# show interface c3/0 sid connectivity Router# show interface c3/0 sid counters verboseShow ConnectivityRouter# show interface c3/0 sid 1 counters Troubleshooting Using Cable Flap Lists Show Cable QoS ProfileUBR7200#show cable qos profile Page Page Display the Flap List UBR7200#show cable flapStatistic Description MAC IDPlant troubleshooting. The CRC counter indicates Troubleshoot with the Flap List Verify Cable Flap List Aging Set Cable Flap List AgingSet Cable Flap List Insertion Time Verify Cable Flap List Insertion TimeSet Cable Flap List Power Adjustment Threshold Verify Cable Flap List Power Adjustment ThresholdSet Cable Flap List Miss Threshold Verify Cable Flap List Miss Threshold Set Cable Flap List SizeClear Cable Flap List Verify Cable Flap List SizeCustomize Other Flap List Values and Related Commands Enable or Disable Power Adjustment Performing Amplitude AveragingSet Frequency Threshold to Affect Power Adjustment Syntax Valid ValuesSetting Downstream Test Signals Configure Unmodulated Test SignalsStep Command Purpose Step Command Configure Prbs Test SignalsVerify Test Signal Output Pinging Unresponsive Cable ModemsUsing Cable Interface Debug Commands Verify the PingDebug Cable ARP Requests Activate Debug of Baseline Privacy Debug Cable MAC Protocol ErrorsDebug Environmental Monitor Messages Debug Baseline Privacy ActivityDebug Cable PHY Messages Debug Cable MapsDebug Cable Modems Activate QoS DebugDebug Upstream Messages Debug Cable Modem Reset MessagesDebug Cable Modem Ranging Messages Debug Cable Modem Registration RequestsDebug Cmts Transmissions Debug Spectrum ManagementDebug Channel Allocations Debug Upstream Channel Change UCC MessagesClear Clock Counters Managing the Cisco uBR7246 VXR Clock CardDebug Upstream Channel Description UCD Messages Show diag Show frame-clocks Show tech support Show versionDisplay Clock Values Force Alternate ClockSet Midplane TDM Clock as Primary Reference Cable clock force primary secondary no cable clock forceRouter# show cable clock Show Clock Diagnostic InformationShow Clock Hardware Information and Register Values Show controllers clock-reference33 describes the fields shown in the show diag display Show Clock Frames Show General InformationRouter# show frame-clocks