Cisco Systems uBR7200 Series manual Crc

Page 26

Chapter 4 Troubleshooting the System

Understanding Show Command Responses

Table 4-16 Show Interface Cable Command Field Descriptions (continued)

Field

Description

drops

Indicates the number of packets dropped due to a full

 

queue

 

 

Five minute input rate

Average number of bits and packets transmitted per second

Five minute output rate

in the last five minutes

 

 

packets input

Total number of error-free packets received by the system

 

 

bytes input

Total number of bytes, including data and MAC

 

encapsulation, in the error-free packets received by the

 

system

 

 

no buffer

Number of received packets discarded because there was

 

no buffer space in the main system

 

 

Received broadcast

Total number of broadcast or multicast packets received by

 

the interface

 

 

runts

Number of packets that are discarded because they are

 

smaller than the medium’s minimum packet size

 

 

giants

Number of packets that are discarded because they exceed

 

the medium’s maximum packet size

 

 

input errors

Includes runts, giants, no buffers, CRC, frame, overrun,

 

and ignored counts

 

 

CRC

Indicates the number of times the cyclic redundancy

 

checksum generated by the originating LAN station or

 

far-end device does not match the checksum calculated

 

from the data received

 

 

frame

Number of packets received incorrectly (with a CRC error

 

and a non-integer number of octets)

 

 

overrun

Number of times the receiver hardware was unable to

 

forward received data to a hardware buffer because the

 

input rate exceeded the receiver’s ability to handle the data

 

 

ignored

Number of received packets ignored by the interface

 

because the interface hardware ran low on internal buffers

 

 

packets output

Total number of messages transmitted by the system

 

 

bytes

Total number of bytes, including data and MAC

 

encapsulation, transmitted by the system

 

 

underruns

Number of times the transmitter ran faster than the

 

receiving device could handle

 

 

output errors

Sum of all errors that prevented the final transmission of

 

packets out of the interface being examined

 

 

interface resets

Number of times an interface has been completely reset

 

 

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

4-26

78-5897-01

 

 

Image 26
Contents Troubleshooting the System Configure Sync Message Interval Managing Cable Modems on the HFC NetworkActivate Cable Modem Upstream Address Verification Activate Cable Modem AuthenticationVerify Cable Modem Authentication Verify Sync Message IntervalVerify Cable Modem Upstream Address Verification CMTS01config-if#cable source-verify dhcpCMTS01config-if#no cable source-verify CMTS01config-if#cable insertion-interval CMTS01config-if#no cable insertion-intervalCMTS01config-if#cable insertion-interval max AutomaticConfigure Per Modem Filters Configure access lists to be specified on a CMTS01config-if#cable registration-timeout n Configure Cable Modem Registration TimeoutClear Cable Modem Reset Verify Clear Cable Modem Reset Clear Cable Modem CountersConfigure Upstream Rate Limiting and Shaping Configure Traffic ShapingConfigure Downstream Rate Limiting and Shaping Verify Clear Cable Modem CountersToken-bucket CMTS01config-if#nocable upstream n1 rate-limitBlind Strategies and Time Scheduled Combined CMTS01# show interface c3/0 sid 1 countersGuided Frequency Hop Sample output Field DescriptionSpectrum Management Debug and Test Commands Show Cable Hop Command14 Show Cable Hop Parameter Descriptions Debug and Test Commands Polling Cable ModemsAllows you to configure access Enable SnmpConfigure Remote Modem Monitoring Verifying Remote Query InformationMonitoring and Maintaining Remote Querying Understanding Show Command ResponsesGeneral Show Commands Show Cable Modem See the sample command output below Page SID Cable modem cable 3/0 upstream 0 offline Show Cable Modem MaintenanceCable modem cable 3/0 upstream 0 unregistered UBR7200#show cable modem maintenance Show Interface CableMTU CRC Field Description Router# show interface cable 6/0 downstream18 Show Interface Cable Upstream Command Field Descriptions ATP Enhanced Show Interface Upstream Output Show Interface Cable SID Cable slot 3, portRouter# show interface c3/0 sid connectivity Router# show interface c3/0 sid counters verboseShow ConnectivityRouter# show interface c3/0 sid 1 counters UBR7200#show cable qos profile Troubleshooting Using Cable Flap ListsShow Cable QoS Profile Page Page Display the Flap List UBR7200#show cable flapStatistic Description MAC IDPlant troubleshooting. The CRC counter indicates Troubleshoot with the Flap List Verify Cable Flap List Aging Set Cable Flap List AgingSet Cable Flap List Insertion Time Verify Cable Flap List Insertion TimeSet Cable Flap List Miss Threshold Set Cable Flap List Power Adjustment ThresholdVerify Cable Flap List Power Adjustment Threshold Verify Cable Flap List Miss Threshold Set Cable Flap List SizeClear Cable Flap List Verify Cable Flap List SizeCustomize Other Flap List Values and Related Commands Enable or Disable Power Adjustment Performing Amplitude AveragingSet Frequency Threshold to Affect Power Adjustment Syntax Valid ValuesStep Command Purpose Setting Downstream Test SignalsConfigure Unmodulated Test Signals Step Command Configure Prbs Test SignalsVerify Test Signal Output Pinging Unresponsive Cable ModemsDebug Cable ARP Requests Using Cable Interface Debug CommandsVerify the Ping Activate Debug of Baseline Privacy Debug Cable MAC Protocol ErrorsDebug Environmental Monitor Messages Debug Baseline Privacy ActivityDebug Cable PHY Messages Debug Cable MapsDebug Cable Modems Activate QoS DebugDebug Upstream Messages Debug Cable Modem Reset MessagesDebug Cable Modem Ranging Messages Debug Cable Modem Registration RequestsDebug Cmts Transmissions Debug Spectrum ManagementDebug Channel Allocations Debug Upstream Channel Change UCC MessagesClear Clock Counters Managing the Cisco uBR7246 VXR Clock CardDebug Upstream Channel Description UCD Messages Show diag Show frame-clocks Show tech support Show versionDisplay Clock Values Force Alternate ClockSet Midplane TDM Clock as Primary Reference Cable clock force primary secondary no cable clock forceRouter# show cable clock Show Clock Diagnostic InformationShow Clock Hardware Information and Register Values Show controllers clock-reference33 describes the fields shown in the show diag display Router# show frame-clocks Show Clock FramesShow General Information