Cisco Systems OL-4858-07 manual Mwam module cpu logging

Page 15

Chapter 6 Command Reference

Command Details

mwam module cpu logging

To configure the severity level of MWAM logging information to send to the Supervisor module, use the mwam module cpu logging command in global configuration mode. To remove this configuration, use the no form of the command.

mwam module {slot_number all} cpu {processor_number all} logging log_level

no mwam module {slot_number all} cpu {processor_number all} logging log_level

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

slot_number all

Specifies the slot that the module is plugged into or all MWAMs in the

 

chassis

 

 

cpu_number all

Specifies the processor on the MWAM or all processors on the MWAM.

 

 

log_level

Limits the logging of messages to be sent to the Supervisor to a specified

 

level (e.g., if log_level is critical, then emergencies, alerts, and critical

 

events are sent). You can enter the level number or name.

 

emergencies (severity level 0)—system is unusable

 

alerts (severity level 1)— immediate action required

 

critical (severity level 2)—critical condition

 

errors (severity level 3)—error condition

 

warnings (severity level 4)—warning condition

 

notifications (severity level 5)—normal but significant condition

 

informational (severity level 6)—informational message

 

debugging (severity level 7)—debug messages

 

 

The default configuration is logging enabled on all MWAM processors for emergencies.

Global configuration.

ReleaseModification

12.2(14)ZA4

This command was introduced.

 

 

Logging methods may require additional configuration such as the destination IP address for the receiver of the log traffic. To configure the destination IP address, use the logging main-cpucommand.

The following example sets the logging level for all MWAM processors in the chassis to the error logging level:

Sup-7600(config)#mwam module all cpu all logging error

Multiprocessor WAN Application Module User Guide

 

OL-4858-07

6-15

 

 

 

Image 15
Contents Following commands are available at the Supervisor console Command ReferenceFollowing commands are available at the Mwam console Processor Control CommandsReleaseModification Command Modes Command HistoryGlobal configuration Mwam module allowed-vlanMwam module vlan-based Module Port Vlan-basedMwam Module Port Vlan-based Usage Guidelines Exec mode12.29ZA This command was introduced Session slot2003 Sup-7606#sho mwam mod 7 port 1 traffic Following example illustrates the show mwam module commandShow mwam module Sup-7606#sho mwam mod 7 port 1 stateSup-7606#sho mwam mod 7 port 3 state Multiprocessor WAN Application Module User Guide OL-4858-07 Sup-7606config#mwam bootflash access Mwam bootflash accessDefaults Command Modes Command History ConfigurationLogging listen mwam Syntax Description DefaultsThere are no default behavior or values On the MWAM, you have configured processor 2 as follows40-10002 40-10003 40-10004 40-10005 40-10006 Mwam Processor Base UDP Port40-10000 Additional UDP PortRelease Modification Defaults Command Modes Command History Usage GuidelinesThere are no default behavior or values Privileged Exec Execute-onConnection, use the show line linenumber command Sup-7600#execute-on 5 2 log show running-configSlot Mwam module cpu logging Sup-7600config#mwam module all cpu all logging errorSup-7600config#mwam module 5 cpu 2 logging debug Release Modification Show loggingCommand Reference Command Details Router# clear logging slot 6 counts Clear logging slotCounter Description Show processorRoot@mwam-9# Shows the Mwam and process restart log Shows the upgrade logFollowing examples illustrate the show log command Show logReload Root@mwam-9#recover-ios Recover-ios12.9ZA This command was introduced Following example illustrates the normal-ioscommandNormal-ios Use this command to list the image names on the Mwam Following example illustrates the show images commandShow images Following example illustrates the restore command RestoreRoot@mwam-4#show tech-support Reporting a problemFollowing example illustrates the show tech-supportcommand Show tech-supportShow version Syntax Description Mwam config-modeLocal mode 12.31aBW This command was introducedShow Mwam Config-mode Show mwam config-modeLogging main-cpu Mwam-6-4config#logging main-cpu 10000 debug Mwam-6-4config#logging main-cpuShow mwam Following examples illustrate the show mwam command0x214800000x214FFFFF 0x0014800000x0014FFFFF OL-4858-07