Cabletron Systems manual Post-Installation, Installing the WPIM-T1/DDS

Page 21

Installing the WPIM-T1/DDS

WPIM

T1

WPIM Screws

WPIM

Connector

DDS

WPIM

T1/DDS-RT1

WPIM

Connector Pins

Standoffs

Figure 2-1 Installing the WPIM-T1/DDS

2.1.4Post-Installation

1.Reinstall the cover as applicable.

2.Refer to the host platform user’s guide to reinstall the network cables and refer to Appendix A for cabling information for the WPIM-T1/DDS. Do not connect the WAN cable until instructed to do so.

3.Refer to instructions contained in the host platform user’s guide to reapply power.

4.After reapplying power, check the LEDs for the following conditions:

•Verify that the PWR LED is on, indicating that the device is receiving power.

•After the host platform runs a self test, the CPU LED blinks green indicating normal operation.

•If the CPU LED remains red, contact Cabletron Systems.

WPIM-T1/DDS User’s Guide

2-3

Image 21

Contents WPIM-T1/DDS User’s Guide Page WPIM-T1/DDS User’s Guide Industry Canada Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Declaration of Conformity WPIM-T1/DDS User’s Guide Contents Viii WPIM-T1/DDS User’s Guide Using this Manual IntroductionStructure of this Guide Related Manuals Following conventions are used throughout this document Document ConventionsYour email address Getting HelpChapter Overview WPIM-T1/DDS Features Firmware RevisionImportant Notice MIB Support WAN ProtocolsOverview WPIM-T1/DDS User’s Guide Chapter Setup and Installation Installing the WPIM-T1/DDSUnpacking the WPIM-T1/DDS Installing the WPIM-T1/DDS Pre-InstallationInstalling the WPIM-T1/DDS Post-InstallationChoosing T1 or DDS Mode LEDsRequired Operations WAN Conﬁguration WAN Connection to the WPIM-T1/DDS Connecting the WAN Cable to the WPIM-T1/DDSChapter Local Management for T1 Service Wpim # WAN Physical Configuration ScreenWAN Physical Conﬁguration Screen Fields Saves the chosen conﬁguration Wpim Line Conﬁguration FieldsWpim Timeslot Conﬁguration Table Sample Timeslot Conﬁguration ANSI94 WAN Interface Configuration ScreenFrame Relay as the Protocol Manager WAN Interface Conﬁguration Screen FieldsWAN Interface Conﬁguration Screen PPP PPP as the Protocol ManagerCommand and Interface Table Fields Telco Conﬁguration Information Full T1 Configuration Using PPP1 T1 Service Physical Conﬁguration 2 T1 Interface Conﬁguration Fractional T1 Conﬁguration Fractional T1 Configuration Using PPP1 T1 Physical Conﬁguration Proceed to the .4.2 to continue configuration Frame Relay Conﬁguration Frame Relay ConfigurationFrame Relay Physical Conﬁguration Frame Relay Conﬁguration Frame Relay Interface Conﬁguration Frame Relay Conﬁguration WPIM-T1/DDS User’s Guide Chapter Local Management for DDS Service Local Management for DDS Service Displays conﬁguration information for two different WPIMs Not used for the WPIM-T1/DDS Invalid Refer to -2for the following parameters displayed for FR Refer to -3for the following parameters displayed for PPP Command and Interface Table Fields DDS Service Physical Conﬁguration DDS Service ConfigurationEnter DDS Service Interface ConﬁgurationDDS Service Conﬁguration WPIM-T1/DDS User’s Guide Physical Properties Appendix a SpecificationsEnvironmental Requirements Regulatory ComplianceCable Assemblies and Pinouts T1 Interface CablingT1 Interface Cabling DDS Port Assignment PIN SignalFCC Part 68 USER’S Information Appendix BAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires