Cabletron Systems manual LEDs, Required Operations, Choosing T1 or DDS Mode

Page 22

Chapter 2: Setup and Installation

2.2LEDs

The LEDs on the WPIM-T1/DDS indicate the service that the WPIM-T1/DDS is providing. (See Figure 2-2.) If the T1 LED is lit, the WPIM-T1/DDS is operating in T1 mode. If the DDS LED is lit, the WPIM-T1/DDS is operating in DDS mode.

T1 Service	DDS Service

T1

DDS

WPIM

T1/DDS

Figure 2-2 LED Indicators

The host platform displays LED indications of the WPIM-T1/DDS’s operation. For more information on host platform LEDs, refer to the host platform manual.

2.3REQUIRED OPERATIONS

The WPIM-T1/DDS must be conﬁgured before connecting to the WAN. The conﬁguration must be performed in the following order:

•Choose T1 or DDS mode (Section 2.3.1)

•WAN conﬁguration, using QuickSET or Local Management (Section 2.3.2)

2.3.1Choosing T1 or DDS Mode

The mode (T1 or DDS) must be chosen before either QuickSET or Local Management is used to conﬁgure the WAN set up.

NOTE

The WPIM-T1/DDS cannot operate in both T1 and DDS mode at the same time. The user must choose one or the other service, but can change it when desired.

When the WPIM-T1/DDS is ﬁrst powered up, the default is T1.

2-4	WPIM-T1/DDS User’s Guide

Image 22

Contents WPIM-T1/DDS User’s Guide Page WPIM-T1/DDS User’s Guide Industry Canada Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Declaration of Conformity WPIM-T1/DDS User’s Guide Contents Viii WPIM-T1/DDS User’s Guide Introduction Using this ManualStructure of this Guide Related Manuals Document Conventions Following conventions are used throughout this documentGetting Help Your email addressChapter Overview Firmware Revision WPIM-T1/DDS FeaturesImportant Notice WAN Protocols MIB SupportOverview WPIM-T1/DDS User’s Guide Installing the WPIM-T1/DDS Chapter Setup and InstallationUnpacking the WPIM-T1/DDS Pre-Installation Installing the WPIM-T1/DDSPost-Installation Installing the WPIM-T1/DDSLEDs Choosing T1 or DDS ModeRequired Operations WAN Conﬁguration Connecting the WAN Cable to the WPIM-T1/DDS WAN Connection to the WPIM-T1/DDSChapter Local Management for T1 Service WAN Physical Configuration Screen Wpim #WAN Physical Conﬁguration Screen Fields Wpim Line Conﬁguration Fields Saves the chosen conﬁgurationWpim Timeslot Conﬁguration Table Sample Timeslot Conﬁguration WAN Interface Configuration Screen ANSI94WAN Interface Conﬁguration Screen Fields Frame Relay as the Protocol ManagerPPP as the Protocol Manager WAN Interface Conﬁguration Screen PPPCommand and Interface Table Fields Full T1 Configuration Using PPP Telco Conﬁguration Information1 T1 Service Physical Conﬁguration 2 T1 Interface Conﬁguration Fractional T1 Configuration Using PPP Fractional T1 Conﬁguration1 T1 Physical Conﬁguration Proceed to the .4.2 to continue configuration Frame Relay Configuration Frame Relay ConﬁgurationFrame Relay Physical Conﬁguration Frame Relay Conﬁguration Frame Relay Interface Conﬁguration Frame Relay Conﬁguration WPIM-T1/DDS User’s Guide Chapter Local Management for DDS Service Local Management for DDS Service Displays conﬁguration information for two different WPIMs Not used for the WPIM-T1/DDS Invalid Refer to -2for the following parameters displayed for FR Refer to -3for the following parameters displayed for PPP Command and Interface Table Fields DDS Service Configuration DDS Service Physical ConﬁgurationDDS Service Interface Conﬁguration EnterDDS Service Conﬁguration WPIM-T1/DDS User’s Guide Environmental Requirements Appendix a SpecificationsPhysical Properties Regulatory ComplianceT1 Interface Cabling Cable Assemblies and PinoutsT1 Interface Cabling PIN Signal DDS Port AssignmentAppendix B FCC Part 68 USER’S InformationAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires