Cabletron Systems T1 manual Industry Canada Notice

Page 4

Notice

INDUSTRY CANADA NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements documents (s). The department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence Numbers of all the devices does not exceed 5.

VCCI NOTICE

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

ii

WPIM-T1/DDS User’s Guide

Image 4
Contents WPIM-T1/DDS User’s Guide Page WPIM-T1/DDS User’s Guide Industry Canada Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Declaration of Conformity WPIM-T1/DDS User’s Guide Contents Viii WPIM-T1/DDS User’s Guide Introduction Using this ManualStructure of this Guide Related Manuals Document Conventions Following conventions are used throughout this documentGetting Help Your email addressChapter Overview Firmware Revision WPIM-T1/DDS FeaturesImportant Notice WAN Protocols MIB SupportOverview WPIM-T1/DDS User’s Guide Installing the WPIM-T1/DDS Chapter Setup and InstallationUnpacking the WPIM-T1/DDS Pre-Installation Installing the WPIM-T1/DDSPost-Installation Installing the WPIM-T1/DDSLEDs Choosing T1 or DDS ModeRequired Operations WAN Configuration Connecting the WAN Cable to the WPIM-T1/DDS WAN Connection to the WPIM-T1/DDSChapter Local Management for T1 Service WAN Physical Configuration Screen Wpim #WAN Physical Configuration Screen Fields Wpim Line Configuration Fields Saves the chosen configurationWpim Timeslot Configuration Table Sample Timeslot Configuration WAN Interface Configuration Screen ANSI94WAN Interface Configuration Screen Fields Frame Relay as the Protocol ManagerPPP as the Protocol Manager WAN Interface Configuration Screen PPPCommand and Interface Table Fields Full T1 Configuration Using PPP Telco Configuration Information1 T1 Service Physical Configuration 2 T1 Interface Configuration Fractional T1 Configuration Using PPP Fractional T1 Configuration1 T1 Physical Configuration Proceed to the .4.2 to continue configuration Frame Relay Configuration Frame Relay ConfigurationFrame Relay Physical Configuration Frame Relay Configuration Frame Relay Interface Configuration Frame Relay Configuration WPIM-T1/DDS User’s Guide Chapter Local Management for DDS Service Local Management for DDS Service Displays configuration information for two different WPIMs Not used for the WPIM-T1/DDS Invalid Refer to -2for the following parameters displayed for FR Refer to -3for the following parameters displayed for PPP Command and Interface Table Fields DDS Service Configuration DDS Service Physical ConfigurationDDS Service Interface Configuration EnterDDS Service Configuration WPIM-T1/DDS User’s Guide Appendix a Specifications Physical PropertiesEnvironmental Requirements Regulatory ComplianceT1 Interface Cabling Cable Assemblies and PinoutsT1 Interface Cabling PIN Signal DDS Port AssignmentAppendix B FCC Part 68 USER’S InformationAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires