Cabletron Systems manual Full T1 Configuration Using PPP, Telco Conﬁguration Information

Page 35

Full T1 Conﬁguration Using PPP

3.3FULL T1 CONFIGURATION USING PPP

This section provides step-by-step instructions for conﬁguring the WPIM-T1/DDS to use a full T1 circuit in a PPP environment. This simpliﬁed example assumes the setup shown in Figure 3-6using a CSX400 with a WPIM-T1/DDS installed at Site #1. Conﬁgurations may vary depending on the host platform.

SITE #1

Telco Cloud

24 Timeslots

Figure 3-6 Full T1 Conﬁguration

SITE #2

24 Timeslots

1482_05

The line conﬁguration information shown in Table 3-1must be supplied by the service provider.

Table 3-1 Telco Conﬁguration Information

Conﬁguration Information	Conﬁguration Information
Required by User	Supplied by Service Provider


Line Coding	B8ZS or AMI

Frame Type	ESF or D4

Clock Source	Loop Timing or Local Timing

WPIM-T1/DDS User’s Guide

3-11

Image 35

Contents WPIM-T1/DDS User’s Guide Page WPIM-T1/DDS User’s Guide Industry Canada Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Declaration of Conformity WPIM-T1/DDS User’s Guide Contents Viii WPIM-T1/DDS User’s Guide Structure of this Guide Using this ManualIntroduction Related Manuals Following conventions are used throughout this document Document ConventionsYour email address Getting HelpChapter Overview Important Notice WPIM-T1/DDS FeaturesFirmware Revision MIB Support WAN ProtocolsOverview WPIM-T1/DDS User’s Guide Unpacking the WPIM-T1/DDS Chapter Setup and InstallationInstalling the WPIM-T1/DDS Installing the WPIM-T1/DDS Pre-InstallationInstalling the WPIM-T1/DDS Post-InstallationRequired Operations Choosing T1 or DDS ModeLEDs WAN Conﬁguration WAN Connection to the WPIM-T1/DDS Connecting the WAN Cable to the WPIM-T1/DDSChapter Local Management for T1 Service Wpim # WAN Physical Configuration ScreenWAN Physical Conﬁguration Screen Fields Saves the chosen conﬁguration Wpim Line Conﬁguration FieldsWpim Timeslot Conﬁguration Table Sample Timeslot Conﬁguration ANSI94 WAN Interface Configuration ScreenFrame Relay as the Protocol Manager WAN Interface Conﬁguration Screen FieldsWAN Interface Conﬁguration Screen PPP PPP as the Protocol ManagerCommand and Interface Table Fields Telco Conﬁguration Information Full T1 Configuration Using PPP1 T1 Service Physical Conﬁguration 2 T1 Interface Conﬁguration Fractional T1 Conﬁguration Fractional T1 Configuration Using PPP1 T1 Physical Conﬁguration Proceed to the .4.2 to continue configuration Frame Relay Conﬁguration Frame Relay ConfigurationFrame Relay Physical Conﬁguration Frame Relay Conﬁguration Frame Relay Interface Conﬁguration Frame Relay Conﬁguration WPIM-T1/DDS User’s Guide Chapter Local Management for DDS Service Local Management for DDS Service Displays conﬁguration information for two different WPIMs Not used for the WPIM-T1/DDS Invalid Refer to -2for the following parameters displayed for FR Refer to -3for the following parameters displayed for PPP Command and Interface Table Fields DDS Service Physical Conﬁguration DDS Service ConfigurationEnter DDS Service Interface ConﬁgurationDDS Service Conﬁguration WPIM-T1/DDS User’s Guide Regulatory Compliance Appendix a SpecificationsPhysical Properties Environmental RequirementsCable Assemblies and Pinouts T1 Interface CablingT1 Interface Cabling DDS Port Assignment PIN SignalFCC Part 68 USER’S Information Appendix BAppendix B FCC Part 68 User’s Information Being duly sworn, state My commission expires