Extron electronic ISM 182 manual Installation, cont’d, Captive screw connector wiring for inputs

Page 18

Installation, cont’d

3Input audio connectors — Connect balanced or unbalanced stereo or mono

audio to these 3.5 mm, 5-pole captive screw connectors. Connectors are included with the seamless switcher, but you must supply the audio cable. Figure 2-4 shows how to wire a connector for the appropriate input type and impedance level. High impedance is generally over 800 ohms.

Tip Sleeve

Tip Sleeve

Tip

Ring

Sleeve (s)

Tip

Ring

600 ohms

Tip

Ring

Sleeve (s)

Tip

Ring

 

 

600 ohms

Unbalanced Input

Balanced Input

Balanced Input

(high impedance)

(high impedance)

(600 ohms)

Figure 2-4 — Captive screw connector wiring for inputs

When making connections for the seamless switcher from existing audio cables, see figure 2-5. A mono audio connector consists of the tip and sleeve. A stereo audio connector consists of the tip, ring and sleeve. The ring, tip, and sleeve wires are also shown on the captive screw audio connector diagram, figure 2-4.

Tip (+)

Sleeve ()

Tip (+)

Ring (-)

Sleeve ()

RCA Connector

3.5 mm Stereo Plug Connector

(balanced)

 

Figure 2-5 — Phono audio connectors

The audio level for each input can be individually set, via the front panel, the Ethernet link, or the RS-232 link, to ensure that the level on the output does not vary from input to input. See chapter 3, Operation, chapter 4, Programmer’s Guide, chapter 5, Switcher Software, and chapter 6, Ethernet Operation for details.

2-4 Integration Scaling Matrix Switcher Installation

Image 18
Contents Integration Scaling Matrix Switchers ISM 482 & ISMSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoCabling and RJ-45 connector wiring Ethernet connectionChoosing a network cable Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsOutputs buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioTest Pattern submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageTroubleshooting Optimizing the AudioGeneral checks Specific problems Problem CauseOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressTies creation Switcher-Initiated MessagesPower-up Input and output video typeX2 Col Programmer’s Guide, cont’d Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Command Ascii Command Response Additional description Horizontal size BrightnessContrast Vertical sizeHorizontal detail filter RGB and component video inputs Pixel phaseBottom blanking Vertical detail filter RGB and component video inputsFreeze User presetsAuto Memories Test patternExecutive mode Verbose modeInformation requests Command/response table for IP SIS commands ResetsCommand/response table for special function SIS commands Delay timesScaler settings Blue screen Enhanced modePAL film mode Edge smoothingCommand Hex Command Response Memory backupAdditional description Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareEthernet protocol settings Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoad the Startup Control Control Control Change the RGB delayEthernet Operation, cont’d Create a tieOutput a test pattern Executive modeFreeze the output Preview the scan rateSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressConnect as a Telnet client Telnet tipsOpen Set carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Reference Information, cont’d Optional accessoriesCables and connectors Part NumbersBNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 3 pages 47.89 Kb