Extron electronic ISM 182 manual Quick Start Integration Scaling Matrix Switcher, QS-1

Page 3

Balanced Input

(600 ohms)

Quick Start — Integration Scaling Matrix Switcher

Installation

Step 1

Turn off power to the ISM 182 or ISM 482 and the input and output devices, and remove the power cords from them.

Step 2

Install four rubber feet on the bottom of the ISM or mount the ISM in a rack.

Step 4

Cable the switcher for audio input. Each input has a 3.5 mm, 5-pole captive screw connector for balanced or unbalanced stereo or mono audio input. Connectors are included with each switcher, but you must supply the audio cable. High impedance is generally over 800 ohms.

Tip

Sleeve

Tip

Sleeve

Unbalanced Input

(high impedance)

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Input

(high impedance)

600 ohms

Tip

Ring

Sleeve (s)

Tip

Ring

600 ohms

ISM	482

INPU

TS

Step 3

Connect up to eight computer/RGB video, component video, S-video, or composite video sources to these female BNC input connectors.

The figure below shows how to connect the various video formats.

	Step 5
	Connect RGB video displays to
	the Output 1 and Output 2	R	R
	female BNC and 15-pin HD	R	R
	female BNC and 15-pin HD
	connectors. Connect the
	various video formats to the	G	G
	BNCs as shown.
	Both output connector	B	B
	types output the same
	video signal and the
	same sync format.	H/HV	H/HV
	Step 6	V	V
	Cable the switcher for audio	V	V
	Cable the switcher for audio	RGBHV	RGBS
	output. Each output has a	Video	Video
	3.5 mm, 5-pole captive screw

connector that outputs the selected unamplified, line level audio. Connect an audio device, such as an audio amplifier or powered speakers.

R/R-Y	R/R-Y	R/R-Y	R/R-Y	R/R-Y
G/Y	G/Y	G/Y	G/Y	G/Y
VID	VID	VID	VID	VID
B/C	B/C	B/C	B/C	B/C
B-Y	B-Y	B-Y	B-Y	B-Y

Tip	AUDIO
Tip	AUDIO
See caution
Sleeve
See caution
Unbalanced Output
Tip	AUDIO
Tip	AUDIO
Ring
Sleeve (s)
Ring

Balanced Output

CAUTION Connect the sleeve to ground. Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

H/HV	H/HV	H/HV	H/HV	H/HV
V	V	V	V	V
RGBHV	RGBS or	RGsB or	S-Video	Composite
Video	RGBcvS	Component		Video
	Video	Video

Step 7

If desired, connect a control system or computer to the Remote RS-232 port.

	Pin	RS-232	Function	5	1
	Pin	RS-232	Function
	1	—	Not used
	2	TX	Transmit data
	3	RX	Receive data	9	6
	4	—	Not used	Female
	5	Gnd	Signal ground	1	5
	6	—	Not used	1	5
	6	—	Not used
	7	—	Not used
	8	—	Not used
	9	—	Not used	6	9
				6	9

Male

QS-1

Image 3

Contents ISM 482 & ISM Integration Scaling Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’dExtron ISM Introduction, cont’d FeaturesIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Integration Scaling Matrix Switcher Installation Installationstallation, cont’dMounting the Switcher Tabletop placementInput connections Cabling and Rear Panel ViewsCaptive screw connector wiring for inputs Installation, cont’dBNC output connections for Rgbhv and Rgbs video Output connectionsCabling and RJ-45 connector wiring Ethernet connectionChoosing a network cable RJ-45 connector pinout tables Wiring the network cableRS-232 connection ConfigurationThree Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’dOutputs buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu Resolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 HzVideo & Audio Advanced Configuration menuBlanking submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustments14 Front panel security lockout flowchart Front panel security lockout executive modeIP information Optimizing the VideoControls to position the image Setting up a DVD sourceTroubleshooting Optimizing the AudioGeneral checks Problem Cause Specific problemsOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Default address SymbolsInput and output video type Switcher-Initiated MessagesPower-up Ties creationX2 Col Programmer’s Guide, cont’d Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Command Ascii Command Response Additional description Vertical size BrightnessContrast Horizontal sizeVertical detail filter RGB and component video inputs Pixel phaseBottom blanking Horizontal detail filter RGB and component video inputsTest pattern User presetsAuto Memories FreezeExecutive mode Verbose modeInformation requests Resets Command/response table for IP SIS commandsCommand/response table for special function SIS commands Delay timesScaler settings Edge smoothing Enhanced modePAL film mode Blue screenCommand Hex Command Response Memory backupAdditional description Five Control Software for Windows Installing the softwareEthernet protocol settings Integration Scaling Matrix Switcher Switcher SoftwareIf you selected a comm port, proceed to step Using the control programWindows Control program window Switcher Software, cont’dButton-Label Generator Using the help programUsing the software Installing the softwareSix Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoad the Startup Control Control Create a tie Change the RGB delayEthernet Operation, cont’d ControlPreview the scan rate Executive modeFreeze the output Output a test patternSystem Configuration System ConfigurationISM Name field Administration fieldsISM IP Settings fields ISM IP Address fieldFile Management File ManagementI/O Configuration Input configurationOutput resolution, rate, sync format, and polarity Output rate Output resolutionOutput polarity Output formatAAppendix a Ethernet Connection, cont’d Integration Scaling Matrix Switcher Ethernet ConnectionPing to determine the Web IP address Ping to determine the switcher’s IP addressConnect as a Telnet client Telnet tipsOpen Close Escape character and Esc keyLocal echo Set carriage return-line feedEthernet Connection, cont’d AppendixBB Integration Scaling Matrix Switcher Reference Information SpecificationsAudio Part Numbers Optional accessoriesCables and connectors Reference Information, cont’dPlenum BNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA

Related manuals

Manual 3 pages 47.89 Kb