Extron electronic ISM 182 Command Hex Command Response, Additional description, Memory backup

Page 60

Programmer’s Guide, cont’d

Command/response table for advanced instruction set commands

The advanced instruction set consist of four hexadecimal commands for uploading and downloading all or a portion of the switcher’s memory. These commands are for use by knowledgeable programmers, and result in a dump of data from (upload) or to (download) the switcher. Programmers can use the commands to exactly duplicate the settings among switchers with a minimum of effort.

Command	Hex Command			Response		Additional description
	(host to switcher)			(switcher to host)
Memory backup
Read all memory contents	90 91			{8226 data bytes+1 byte checksum}		Upload (switcher to control
						device) all color, tint, contrast,
						brightness, detail, sizing, and
						centering settings; all user presets;
						and all auto memories for all
						inputs and both outputs.
Write all memory contents	90 92+8226 data bytes+1 byte checksum				Dn1	Download (control device to
						switcher) all color, tint, contrast,
						brightness, detail, sizing, and
						centering settings; all user presets;
						and all auto memories for all
						inputs and both outputs.
Read partial contents			90 93	{26 data bytes+1 byte checksum}		Upload (switcher to control
Read partial contents		X2	90 93	{26 data bytes+1 byte checksum}		Upload (switcher to control
						device) color, tint, contrast,
						brightness, detail, sizing, and
						centering settings; all user presets;

and all auto memories for the input selected for output X2 .

Write partial contents

X2	90 94+26 data bytes+1 byte checksum	Dn1	Download (control device to
			switcher) color, tint, contrast,
			brightness, detail, sizing, and
			centering settings; all user presets;
			and all auto memories for the
			input selected for output		.
			input selected for output	X2	.

4-16 Integration Scaling Matrix Switcher • Programmer’s Guide

Image 60

Contents Integration Scaling Matrix Switchers ISM 482 & ISMSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About the Switcher Integration Scaling Matrix Switcher IntroductionIntroductiontroduction, cont’d About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoCabling and RJ-45 connector wiring Ethernet connectionChoosing a network cable Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Front Panel Controls and Indicators Integration Scaling Matrix Switcher OperationOperationeration, cont’d Video/Audio selection button and LEDsOutputs buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioBlue Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenuEnhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageTroubleshooting Optimizing the AudioGeneral checks Specific problems Problem CauseOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressSwitcher-Initiated Messages Power-upTies creation Input and output video typeX2 Col Programmer’s Guide, cont’d Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Command Ascii Command Response Additional description Brightness ContrastHorizontal size Vertical sizePixel phase Bottom blankingHorizontal detail filter RGB and component video inputs Vertical detail filter RGB and component video inputsUser presets Auto MemoriesFreeze Test patternExecutive mode Verbose modeInformation requests Command/response table for IP SIS commands ResetsCommand/response table for special function SIS commands Delay timesScaler settings Enhanced mode PAL film modeBlue screen Edge smoothingCommand Hex Command Response Memory backupAdditional description Five Installing the software Ethernet protocol settingsIntegration Scaling Matrix Switcher Switcher Software Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoad the Startup Control Control Change the RGB delay Ethernet Operation, cont’dControl Create a tieExecutive mode Freeze the outputOutput a test pattern Preview the scan rateSystem Configuration System ConfigurationAdministration fields ISM IP Settings fieldsISM IP Address field ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressConnect as a Telnet client Telnet tipsOpen Escape character and Esc key Local echoSet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Optional accessories Cables and connectorsReference Information, cont’d Part NumbersAssorted connectors BNC connectors BNC-4 Mini HR CableBNC-5 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA

Related manuals

Manual 3 pages 47.89 Kb