Extron electronic ISM 182 manual Operation, cont’d, Black/Mute button and LEDs

Page 26

Operation, cont’d

Selecting an input

4Input selection buttons — The Input 1 through Input 8 buttons select the associated input to scale and display on the selected output(s).

Input selection LEDs — The green input LEDs above the input buttons indicate the video selection. The red input LEDs below the input buttons indicate the audio selection. To view the input tied to the unselected output, press the unselected output button. Both outputs’ input selections can also be viewed in the LCD display cycle.

Recalling a user preset

There are three user presets per input. The presets save color, tint, contrast, brightness, detail, sizing, and centering settings. See User Presets menu later in this chapter to save and erase presets. Cycle through and recall these memories by repeatedly pressing the appropriate input button. The LCD panel identifies the recalled preset (figure 3-5).

Press button

3

Press button

3

Press button

3

3

User Preset #2

User Preset #3

User Preset #1

User Preset #2

Recalled

Recalled

Recalled

Recalled

Figure 3-5 — Recalling user presets

Auto imaging an input

The auto imaging feature automatically sizes and centers the selected input to fill the screen. Initiate the auto imaging feature for a specific input by pressing and holding the appropriate input button until the LCD displays the message Auto Image Input #n, releasing the input button, and then pressing and releasing the input button again. The LCD displays AutoSizing and Centering Please Wait... until the operation is complete. Alternatively, using the menu system, this feature can be set to apply the Auto Image adjustments to every input as it is selected (see Auto Imaging and Auto Memories submenu later in this chapter).

Black/Mute button and LEDs

5Black/Mute button and LEDs — The Black/Mute button switches the selected output(s) to a black screen and/or muted audio. The black screen and/or mute audio is deselected when a new input is selected.

Picture adjustment buttons

6The picture adjustment buttons select individual image adjustments that are adjusted using the Adjust and Adjust knobs ( 9 ). The LEDs above these buttons light when the button is pressed.

Color/Tint control button — The Color/Tint button selects the display color and tint adjustments. The color adjustment range is from 0 to 127. The tint adjustment range is from 0 to 255. See Picture adjustments in this chapter.

The Color/Tint control affects only composite video and S-video inputs.

3-4 Integration Scaling Matrix Switcher • Operation

Image 26
Contents Integration Scaling Matrix Switchers ISM 482 & ISMSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoChoosing a network cable Cabling and RJ-45 connector wiringEthernet connection Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsFront panel input label window Outputs buttons and LEDsInput buttons, LEDs, and label window Black/Mute button and LEDs Picture adjustment buttonsOperation, cont’d Menu control buttons Adjustment knobsLCD display Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioTest Pattern submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageGeneral checks TroubleshootingOptimizing the Audio Specific problems Problem CauseOperation, cont’d Four Ethernet Link Integration Scaling Matrix Switcher Programmer’s GuideRS-232 Link Symbols Default addressTies creation Switcher-Initiated MessagesPower-up Input and output video typeX2 Col Programmer’s Guide, cont’d Using the command/response table Host-to-Switcher InstructionsSwitcher error responses Command Ascii Command Response Additional description Horizontal size BrightnessContrast Vertical sizeHorizontal detail filter RGB and component video inputs Pixel phaseBottom blanking Vertical detail filter RGB and component video inputsFreeze User presetsAuto Memories Test patternInformation requests Executive modeVerbose mode Command/response table for IP SIS commands ResetsScaler settings Command/response table for special function SIS commandsDelay times Blue screen Enhanced modePAL film mode Edge smoothingAdditional description Command Hex Command ResponseMemory backup Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareEthernet protocol settings Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix Load the Startup Control Integration Scaling Matrix Switcher Ethernet OperationEthernetOperation,cont’d Control Control Change the RGB delayEthernet Operation, cont’d Create a tieOutput a test pattern Executive modeFreeze the output Preview the scan rateSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressOpen Connect as a Telnet clientTelnet tips Set carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Reference Information, cont’d Optional accessoriesCables and connectors Part NumbersBNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 3 pages 47.89 Kb