Extron electronic ISM 182 Administration fields, ISM IP Settings fields, ISM IP Address field

Page 73

Administration fields

•Ethernet connection to the switcher, either by entering SIS commands (see chapter 4, Programmer’s Guide) or using the Control Program (see chapter 5, Switcher Software) is password protected.

•Connection via HTML pages and connection via the RS-232 port are not password protected.

On password-protected connections, there are two levels of protection: administrator and user. Administrators have full access to all ISM switching capabilities and editing functions. Users can select video and/or audio for output, select test patterns, set RGB and audio mutes, select a blue screen, and view all settings with the exception of passwords.

The administration fields on the System Configuration page are for entering and verifying administrator and user passwords. Passwords are case sensitive and are limited to 12 upper case and lower case alphanumeric characters. Each password must be entered twice; once in the password field and then repeated in the re-enter password field. Characters in these fields are masked by asterisks (*****). If you do not want to password protect an access level, leave the password field and the re- enter password field blank. After entering the desired password in both fields, click the Submit button.

If a password has been inadvertently changed to an unknown value, you can still connect to the switcher via the RS-232 link, which is not password protected. When connected via the RS-232 link, using either SIS commands (see chapter 4, Programmer’s Guide) or under Windows program control (see chapter 5, Switcher Software), you can look up and, if desired, change a password.

ISM IP Settings fields

The ISM IP Settings fields provides a location for observing and editing settings unique to the Ethernet interface. After editing any of the settings on this page, click the Submit button.

ISM IP Address field

The ISM IP Address field contains the IP address of the connected ISM. This value is encoded in the flash memory on the controller circuit board.

Valid IP addresses consist of four 1-, 2-, or 3-digit numeric subfields separated by dots (periods). Each field can be numbered from 000 through 255. Leading zeroes, up to 3 digits total per field, are optional. Values of 256 and above are invalid.

The default address is 192.168.254.254, but if this conflicts with other equipment at your installation, you can change the IP address to any valid value.

ISM Name field

The ISM Name field contains the name of the switcher. This is helpful in identifying the switcher in multiple-unit networks. This name field can be changed to any valid name, up to 12 alphanumeric characters.

Hardware Address field

The Hardware Address is hardcoded on the controller board and cannot be changed.

Integration Scaling Matrix Switcher • Ethernet Operation

6-7

Page 72 Page 74
Image 73
Page 72 Page 74
Contents ISM 482 & ISM Integration Scaling Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Integration Scaling Matrix Switcher Introduction About the SwitcherIntroductiontroduction, cont’d About this ManualExtron ISM Introduction, cont’d FeaturesIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Mounting the Switcher Installationstallation, cont’dTabletop placement Integration Scaling Matrix Switcher InstallationInput connections Cabling and Rear Panel ViewsCaptive screw connector wiring for inputs Installation, cont’dBNC output connections for Rgbhv and Rgbs video Output connectionsEthernet connection Cabling and RJ-45 connector wiringChoosing a network cable RJ-45 connector pinout tables Wiring the network cableRS-232 connection ConfigurationThree Integration Scaling Matrix Switcher Operation Front Panel Controls and IndicatorsOperationeration, cont’d Video/Audio selection button and LEDsInput buttons, LEDs, and label window Outputs buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu Resolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 HzVideo & Audio Advanced Configuration menuRGB Delay submenu Blue Only Mode and Edge Smoothing submenuTest Pattern submenu Blanking submenuPixel Phase submenu Enhanced Mode submenuPAL Film Mode submenu Reset submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustments14 Front panel security lockout flowchart Front panel security lockout executive modeIP information Optimizing the VideoControls to position the image Setting up a DVD sourceOptimizing the Audio TroubleshootingGeneral checks Problem Cause Specific problemsOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Default address SymbolsPower-up Switcher-Initiated MessagesTies creation Input and output video typeX2 Col Programmer’s Guide, cont’d Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Command Ascii Command Response Additional description Contrast BrightnessHorizontal size Vertical sizeBottom blanking Pixel phaseHorizontal detail filter RGB and component video inputs Vertical detail filter RGB and component video inputsAuto Memories User presetsFreeze Test patternVerbose mode Executive modeInformation requests Resets Command/response table for IP SIS commandsDelay times Command/response table for special function SIS commandsScaler settings PAL film mode Enhanced modeBlue screen Edge smoothingMemory backup Command Hex Command ResponseAdditional description Five Ethernet protocol settings Installing the softwareIntegration Scaling Matrix Switcher Switcher Software Control Software for WindowsIf you selected a comm port, proceed to step Using the control programWindows Control program window Switcher Software, cont’dButton-Label Generator Using the help programUsing the software Installing the softwareSix EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoad the Startup Control Control Ethernet Operation, cont’d Change the RGB delayControl Create a tieFreeze the output Executive modeOutput a test pattern Preview the scan rateSystem Configuration System ConfigurationISM IP Settings fields Administration fieldsISM IP Address field ISM Name fieldFile Management File ManagementI/O Configuration Input configurationOutput resolution, rate, sync format, and polarity Output rate Output resolutionOutput polarity Output formatAAppendix a Ethernet Connection, cont’d Integration Scaling Matrix Switcher Ethernet ConnectionPing to determine the Web IP address Ping to determine the switcher’s IP addressTelnet tips Connect as a Telnet clientOpen Local echo Escape character and Esc keySet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Integration Scaling Matrix Switcher Reference Information SpecificationsAudio Cables and connectors Optional accessoriesReference Information, cont’d Part NumbersBNC-4 Mini HR Cable Assorted connectors BNC connectorsBNC-5 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 3 pages 47.89 Kb
Top Page Image Contents