Extron electronic ISM 182 manual Optimizing the Video, IP information

Page 40

Operation, cont’d

IP information

To set up the ISM for operation via its Ethernet port, you need to know and be able to change the IP address. One way to do this is via the IP address and hardware address screen.

To access the IP address and hardware address screen, press and hold the Color/Tint and Detail buttons while you apply power to the ISM (figure 3-15). When the ISM is finished intializing, it displays both addresses.

Press and hold both buttons

simultaneously while applying power

COLOR/

TINT

DETAIL

IP Address

Power

>192.168.254.254 Hardware Address 00-80-00-00-04-04

Select the IP address subfield	Change the subfield value
with the Adjust knob.	with the Adjust knob.

IP Address 192.168.254>253

Hardware Address 00-80-00-00-04-04

10 sec.	NOTE The hardware address is
	hardcoded and cannot
Default	be changed.
Cycle

Figure 3-15 — IP information flowchart

If you need to change the IP address, use the Adjust knob to select the desired subfield. Rotate the Adjust knob to change the value. Repeat the adjustment for other subfields as required.

Valid IP addresses consist of four 1-, 2-, or 3-digit numeric subfields separated by dots (periods). Each field can be numbered from 000 through 255. Leading zeroes, up to 3 digits total per field, are optional. Values of 256 and above are invalid.

If the local system administrators have not changed the value, the factory- specified default, 192.168.254.254, is the correct value for this field.

The hardware address is hardcoded and cannot be changed.

Optimizing the Video

Perform the following steps, in sequence, after you have installed the ISM. This procedure will help you to configure the switcher for the best settings for your display environment. In a multi-screen environment, perform this procedure for each display.

See Advanced Configuration menu earlier in this chapter to select and output a test pattern and to select and output blue only video.

See Picture adjustments earlier in this chapter to make adjustments to the picture quality.

See User Presets menu earlier in this chapter to save presets.

3-18 Integration Scaling Matrix Switcher • Operation

Image 40

Contents Integration Scaling Matrix Switchers ISM 482 & ISMSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About the Switcher Integration Scaling Matrix Switcher IntroductionIntroductiontroduction, cont’d About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoEthernet connection Cabling and RJ-45 connector wiringChoosing a network cable Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Front Panel Controls and Indicators Integration Scaling Matrix Switcher OperationOperationeration, cont’d Video/Audio selection button and LEDsInput buttons, LEDs, and label window Outputs buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioBlue Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenuEnhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageOptimizing the Audio TroubleshootingGeneral checks Specific problems Problem CauseOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Symbols Default addressSwitcher-Initiated Messages Power-upTies creation Input and output video typeX2 Col Programmer’s Guide, cont’d Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Command Ascii Command Response Additional description Brightness ContrastHorizontal size Vertical sizePixel phase Bottom blankingHorizontal detail filter RGB and component video inputs Vertical detail filter RGB and component video inputsUser presets Auto MemoriesFreeze Test patternVerbose mode Executive modeInformation requests Command/response table for IP SIS commands ResetsDelay times Command/response table for special function SIS commandsScaler settings Enhanced mode PAL film modeBlue screen Edge smoothingMemory backup Command Hex Command ResponseAdditional description Five Installing the software Ethernet protocol settingsIntegration Scaling Matrix Switcher Switcher Software Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoad the Startup Control Control Change the RGB delay Ethernet Operation, cont’dControl Create a tieExecutive mode Freeze the outputOutput a test pattern Preview the scan rateSystem Configuration System ConfigurationAdministration fields ISM IP Settings fieldsISM IP Address field ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressTelnet tips Connect as a Telnet clientOpen Escape character and Esc key Local echoSet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Optional accessories Cables and connectorsReference Information, cont’d Part NumbersAssorted connectors BNC connectors BNC-4 Mini HR CableBNC-5 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA

Related manuals

Manual 3 pages 47.89 Kb