Extron electronic ISM 182 Ethernet Operation, cont’d, Control, Create a tie, Change the RGB delay

Page 70

Ethernet Operation, cont’d

Control Page

On the Control page (figure 6-1), you can select an input to either or both outputs. The Control page also provides facilities to check the frequency of an input and to mute outputs. Access the Control page by clicking the Control tab.

Create a tie

Select and switch an input to an output as follows:

1.

Click the Video/Audio, Video, or Audio button to select both the video and audio

 

planes, the video plane only, or the audio plane only for switching (audio

 

follow or audio breakaway).

2.

Select an input for output 1 or output 2 by clicking the desired input button

 

for either output 1 or output 2. After the RGB delay, the selected input is

displayed on the designated monitors. The selected input button turns blue to indicate a video and audio or video only selection and yellow to indicate an audio only selection. The RGB delay is user-selectable, see Change the RGB delay, below.

Change the RGB delay

The RGB delay interval for each output defines how long the screen is blanked when selecting a new input for the connected monitor.

Change the RGB delay for an output as follows:

1. Click the RGB Delay field for the desired output. A drop down scroll box appears (figure 6-3).

Figure 6-3 — RGB delay scroll box

2.

Click and drag on either the slider or click the scroll up ( ) or scroll down ( )

 

buttons until the desired interval is visible.

3.

Click the desired output.

Black out the screen and mute the audio

You can mute the video (blackout the screen) and/or audio to output 1 and/or output 2 from the control page as follows:

1.

Click the Video/Audio, Video, or Audio button to select both the video and audio

 

planes, the video plane only, or the audio plane only for muting.

2.

Click the Output 1 or Output 2 Black/Mute button. The Black/Mute button

 

turns blue to indicate a video and audio mute or video only mute or yellow to

indicate audio mute. If you muted the output that is selected on the front panel, the front panel Black and/or Mute LEDs light.

Click the Black/Mute button again to unmute the video and/or audio.

6-4 Integration Scaling Matrix Switcher • Ethernet Operation

Image 70
Contents Integration Scaling Matrix Switchers ISM 482 & ISMSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoEthernet connection Cabling and RJ-45 connector wiringChoosing a network cable Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsInput buttons, LEDs, and label window Outputs buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioTest Pattern submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageOptimizing the Audio TroubleshootingGeneral checks Specific problems Problem CauseOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Symbols Default addressTies creation Switcher-Initiated MessagesPower-up Input and output video typeX2 Col Programmer’s Guide, cont’d Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Command Ascii Command Response Additional description Horizontal size BrightnessContrast Vertical sizeHorizontal detail filter RGB and component video inputs Pixel phaseBottom blanking Vertical detail filter RGB and component video inputsFreeze User presetsAuto Memories Test patternVerbose mode Executive modeInformation requests Command/response table for IP SIS commands ResetsDelay times Command/response table for special function SIS commandsScaler settings Blue screen Enhanced modePAL film mode Edge smoothingMemory backup Command Hex Command ResponseAdditional description Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareEthernet protocol settings Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoad the Startup Control Control Control Change the RGB delayEthernet Operation, cont’d Create a tieOutput a test pattern Executive modeFreeze the output Preview the scan rateSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressTelnet tips Connect as a Telnet clientOpen Set carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Reference Information, cont’d Optional accessoriesCables and connectors Part NumbersBNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 3 pages 47.89 Kb