Extron electronic ISM 182 manual Test Pattern submenu, Blue Only Mode and Edge Smoothing submenu

Page 34

Operation, cont’d

Test Pattern submenu

The Test Pattern submenu lets you select from among several test patterns and assign the selected pattern to an output. The test patterns are helpful when adjusting the connected displays for color, convergence, focus, resolution, contrast, grayscale, and aspect ratio.

Use the Adjust knob to select a test pattern. The options are: Color Bars, crosshatch, 4 x 4 crosshatch, gray scale, crop, alternating pixels, film aspect ratios 1.78, 1.85, 2.35, and ramp.

Use the Adjust knob to assign the output(s) for the selected test pattern. Select among neither output (both off), output 2, output 1, or both outputs.

Blue Only Mode and Edge Smoothing submenu

The Blue Only Mode and Edge Smoothing submenu lets you turn the blue mode and edge smoothing features on and off. Blue-only mode is helpful in the setup of the color and tint of the incoming video signal. In the blue-only mode, only the sync and blue video signals are passed to the display. Edge enhancement mode smooths edges of a picture by minimizing the differences between pixels.

Use the Adjust knob to assign Blue Only Mode to neither output (both off), output 2, output 1, or both outputs. The default is Off.

Use the Adjust knob to assign Edge Smoothing to neither output (both off), output 2, output 1, or both outputs. The default is Off.

Blanking submenu

The Output Blanking submenu displays and allows you to adjust the top and bottom line blanking on the output monitors within a range of 0 to 200 lines. During scaling, captioning and tapehead switching in the video’s blanking area may show up as picture noise. Using blanking, you can add black lines at the top and bottom edges of the image to eliminate edge noise.

Select the output that you want to blank by pressing the desired Output button.

Use the Adjust knob to increase or decrease the top line blanking. The default is 0 lines.

Use the Adjust knob to increase or decrease the bottom line blanking. The default is 0 lines.

RGB Delay submenu

The RGB Delay submenu displays and lets you set the RGB delay when a switch is made. With RGB delay, sync is never removed from the display. Rather, the ISM blanks the RGB (video) outputs while the scaler locks to the new sync, and then switches the RGB signals. This allows a brief delay for the displays to adjust to the new sync timing before displaying the new picture, which will appear without glitches. RGB delay is also known as Triple-Action Switching™ or video mute switching.

Use the Adjust knob to select the blanking period (RGB delay time) for output 1 from 0 seconds to 5 seconds in 0.1 second steps. The default is 0.2 seconds. Use the Adjust knob to select the blanking period for output 2.

3-12 Integration Scaling Matrix Switcher • Operation

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Integration Scaling Matrix Switchers ISM 482 & ISMSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoEthernet connection Cabling and RJ-45 connector wiringChoosing a network cable Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsInput buttons, LEDs, and label window Outputs buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioTest Pattern submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageOptimizing the Audio TroubleshootingGeneral checks Specific problems Problem CauseOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Symbols Default addressTies creation Switcher-Initiated MessagesPower-up Input and output video typeX2 Col Programmer’s Guide, cont’d Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Command Ascii Command Response Additional description Horizontal size BrightnessContrast Vertical sizeHorizontal detail filter RGB and component video inputs Pixel phaseBottom blanking Vertical detail filter RGB and component video inputsFreeze User presetsAuto Memories Test patternVerbose mode Executive modeInformation requests Command/response table for IP SIS commands ResetsDelay times Command/response table for special function SIS commandsScaler settings Blue screen Enhanced modePAL film mode Edge smoothingMemory backup Command Hex Command ResponseAdditional description Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareEthernet protocol settings Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoad the Startup Control Control Control Change the RGB delayEthernet Operation, cont’d Create a tieOutput a test pattern Executive modeFreeze the output Preview the scan rateSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressTelnet tips Connect as a Telnet clientOpen Set carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Reference Information, cont’d Optional accessoriesCables and connectors Part NumbersBNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 3 pages 47.89 Kb
Top Page Image Contents