Extron electronic ISM 182 manual Connect as a Telnet client, Telnet tips, Open

Page 82

Ethernet Connection, cont’d

Connect as a Telnet client

The Microsoft Telnet utility is available from the DOS prompt. Telnet allows you to input SIS commands to the ISM from the PC via the Ethernet link and the LAN.

Access the DOS prompt and start Telnet as follows:

1.

Click on Start > Run.

2.

At the Open prompt, type command.

3.

Click on the OK button.

4.

At the DOS prompt, type telnet and press [Enter]. The computer returns a

 

display similar to figure A-3.

Microsoft (R) windows 2000 (TM) Version 5.0 (Build 2195)

Welcome to Microsoft Telnet Client

Telnet Client Build 5.00.99203.1

Escape Character is 'CTRL+]'

Microsoft Telnet>

Figure A-3 — Telnet screen

Telnet tips

It is not the intention of this manual to detail all of the operations and functionality of Telnet, however some basic level of understanding is necessary for operating the ISM via Telnet.

Open

Connect to the ISM using the Open command. Once you are connected to the switcher, you can enter the SIS commands the same way that you would if you were using the RS-232 link.

Connect to the ISM as follows:

1.

At the Telnet prompt, type open {IP address} and then press [Enter].

 

If the switcher is not password protected, no further prompts are displayed

 

until you break or disconnect the connection to the ISM.

 

If the switcher is password protected, Telnet displays the password prompt.

2.

If necessary, at the password prompt, type {password} and then press [Enter].

 

Connection to the switcher via the Ethernet can be password protected. There

 

are two levels of password protection: administrator and user. A person

logged on as an administrator has full access to all ISM switching capabilities and editing functions. Users can select video and/or audio for output, select test patterns, set RGB and audio mutes, select a blue screen, and view all settings with the exception of passwords. By default, the ISM ships with both passwords cleared (no password assigned).

Once you are logged in, the ISM returns either Login Administrator or Login User. No further prompts are displayed until you break or disconnect the connection to the ISM.

A-4 Integration Scaling Matrix Switcher Ethernet Connection

Image 82
Contents Integration Scaling Matrix Switchers ISM 482 & ISMSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start Integration Scaling Matrix Switcher QS-1Quick Start Integration Scaling Matrix Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Introductiontroduction, cont’d About the SwitcherIntegration Scaling Matrix Switcher Introduction About this ManualExtron ISM Features Introduction, cont’dIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Tabletop placement Installationstallation, cont’dMounting the Switcher Integration Scaling Matrix Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsOutput connections BNC output connections for Rgbhv and Rgbs videoEthernet connection Cabling and RJ-45 connector wiringChoosing a network cable Wiring the network cable RJ-45 connector pinout tablesConfiguration RS-232 connectionThree Operationeration, cont’d Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Video/Audio selection button and LEDsInput buttons, LEDs, and label window Outputs buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Power Front Panel OperationsMenu system overview Extron Electronics ISM 60-425-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioTest Pattern submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Blanking submenuPAL Film Mode submenu Enhanced Mode submenuPixel Phase submenu Reset submenuUser Presets menu Save Preset submenuErase Preset submenu Exit menuPicture adjustments 13 Picture adjustments flowchartFront panel security lockout executive mode 14 Front panel security lockout flowchartOptimizing the Video IP informationSetting up a DVD source Controls to position the imageOptimizing the Audio TroubleshootingGeneral checks Specific problems Problem CauseOperation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Symbols Default addressTies creation Switcher-Initiated MessagesPower-up Input and output video typeX2 Col Programmer’s Guide, cont’d Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Command Ascii Command Response Additional description Horizontal size BrightnessContrast Vertical sizeHorizontal detail filter RGB and component video inputs Pixel phaseBottom blanking Vertical detail filter RGB and component video inputsFreeze User presetsAuto Memories Test patternVerbose mode Executive modeInformation requests Command/response table for IP SIS commands ResetsDelay times Command/response table for special function SIS commandsScaler settings Blue screen Enhanced modePAL film mode Edge smoothingMemory backup Command Hex Command ResponseAdditional description Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareEthernet protocol settings Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Button-Label GeneratorInstalling the software Using the softwareSix EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoad the Startup Control Control Control Change the RGB delayEthernet Operation, cont’d Create a tieOutput a test pattern Executive modeFreeze the output Preview the scan rateSystem Configuration System ConfigurationISM IP Address field Administration fieldsISM IP Settings fields ISM Name fieldFile Management File ManagementInput configuration I/O ConfigurationOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polarityAAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine the Web IP addressTelnet tips Connect as a Telnet clientOpen Set carriage return-line feed Escape character and Esc keyLocal echo CloseEthernet Connection, cont’d AppendixBB Specifications Integration Scaling Matrix Switcher Reference InformationAudio Reference Information, cont’d Optional accessoriesCables and connectors Part NumbersBNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable Plenum BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 3 pages 47.89 Kb