Extron electronic ISM 182 manual Host-to-Switcher Instructions, Switcher error responses

Page 51

1Enh X19

The enhanced mode feature has been turned on or off from the front panel for S-video or composite video tied to one or both outputs. X19 is the on/off status for the two outputs. The leading “1” is meaningless.

X2 Reconfig

The input selected for the X2 output has been adjusted using the Auto Image feature or a user preset.

Host-to-Switcher Instructions

The switcher accepts SIS commands through its RS-232 port and/or its Ethernet port. SIS commands consist of one or more characters per command field. They do not require any special characters to begin or end the command character sequence. Each switcher response to an SIS command ends with a carriage return and a line feed (CR/LF = ), which signals the end of the response character string. A string is one or more characters.

Switcher error responses

When the switcher receives an SIS command and determines that it is valid, it performs the command and sends a response to the host device. If the switcher is unable to perform the command because the command is invalid or contains invalid parameters, the switcher returns an error response to the host. The error response codes are:

E01 — Invalid input channel number (too large)

E10 — Invalid command

E11 — Invalid preset number (zero or too large)

E12 — Invalid output number (zero or too large)

E13 — Invalid value (out of range)

Using the command/response table

The command/response table begins on the next page. Except for the gain and attenuation settings and the filter settings, upper or lower case letters are acceptable in the command field. Command and response examples are shown throughout the table.

The table below shows the hexadecimal equivalent of each ASCII command.

ASCII to HEX Conversion Table

Space

With the exception of the audio gain and attenuation (G and g) and horizontal and vertical filtering (D and d) commands, the SIS commands are not case sensitive.

Integration Scaling Matrix Switcher • Programmer’s Guide

4-7

Image 51

Contents ISM 482 & ISM Integration Scaling Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschQS-1 Quick Start Integration Scaling Matrix SwitcherQS-2 Quick Start Integration Scaling Matrix Switcher, cont’dTable of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’dExtron ISM Introduction, cont’d FeaturesIntegration Scaling Matrix Switcher Introduction Introduction, cont’d Two Integration Scaling Matrix Switcher Installation Installationstallation, cont’dMounting the Switcher Tabletop placementInput connections Cabling and Rear Panel ViewsCaptive screw connector wiring for inputs Installation, cont’dBNC output connections for Rgbhv and Rgbs video Output connectionsCabling and RJ-45 connector wiring Ethernet connectionChoosing a network cable RJ-45 connector pinout tables Wiring the network cableRS-232 connection ConfigurationThree Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’dOutputs buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Front Panel Operations PowerExtron Electronics ISM 60-425-01 Version Menu system overviewInput Configuration submenu Video & Audio Configuration menuOutput Resolution submenu Output Configuration menuSync Type and Polarity submenu Resolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 HzVideo & Audio Advanced Configuration menuBlanking submenu Blue Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenuReset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenuSave Preset submenu User Presets menuExit menu Erase Preset submenu13 Picture adjustments flowchart Picture adjustments14 Front panel security lockout flowchart Front panel security lockout executive modeIP information Optimizing the VideoControls to position the image Setting up a DVD sourceTroubleshooting Optimizing the AudioGeneral checks Problem Cause Specific problemsOperation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Default address SymbolsInput and output video type Switcher-Initiated MessagesPower-up Ties creationX2 Col Programmer’s Guide, cont’d Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Command Ascii Command Response Additional description Vertical size BrightnessContrast Horizontal sizeVertical detail filter RGB and component video inputs Pixel phaseBottom blanking Horizontal detail filter RGB and component video inputsTest pattern User presetsAuto Memories FreezeExecutive mode Verbose modeInformation requests Resets Command/response table for IP SIS commandsCommand/response table for special function SIS commands Delay timesScaler settings Edge smoothing Enhanced modePAL film mode Blue screenCommand Hex Command Response Memory backupAdditional description Five Control Software for Windows Installing the softwareEthernet protocol settings Integration Scaling Matrix Switcher Switcher SoftwareIf you selected a comm port, proceed to step Using the control programWindows Control program window Switcher Software, cont’dButton-Label Generator Using the help programUsing the software Installing the softwareSix Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoad the Startup Control Control Create a tie Change the RGB delayEthernet Operation, cont’d ControlPreview the scan rate Executive modeFreeze the output Output a test patternSystem Configuration System ConfigurationISM Name field Administration fieldsISM IP Settings fields ISM IP Address fieldFile Management File ManagementI/O Configuration Input configurationOutput resolution, rate, sync format, and polarity Output rate Output resolutionOutput polarity Output formatAAppendix a Ethernet Connection, cont’d Integration Scaling Matrix Switcher Ethernet ConnectionPing to determine the Web IP address Ping to determine the switcher’s IP addressConnect as a Telnet client Telnet tipsOpen Close Escape character and Esc keyLocal echo Set carriage return-line feedEthernet Connection, cont’d AppendixBB Integration Scaling Matrix Switcher Reference Information SpecificationsAudio Part Numbers Optional accessoriesCables and connectors Reference Information, cont’dPlenum BNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-4 Mini HR Cable BNC-5 Mini HR CableFirmware Upgrade Installation Figure B-1 Removing the ISM cover Button Labels Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA

Related manuals

Manual 3 pages 47.89 Kb