ATTO Technology 2700C operation manual Front label side, Back connector side

Page 14

Exhibit 1.1-2 Overview of iPBridge 2700R/D from the back (connector) side.

Front label side

			h		Width
			h		17
			t		"
		g			"
	n
e				"
L				"
		7
		.
	8

air vents

Height

1.7"

	RS-232 (serial) port	GbE ports		for bracket

	10/100 Ethernet port		Fibre Channel ports
				assembly

power connector

Back (connector) side

5

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 14

Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface optionsDiagnostic commands CLI commands summary General use commandsMaintenance commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserTarget names Default target nodeTarget management Map devices automaticallyChap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target ManagementUpdating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsFirmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the LAN/WAN Checking the iSCSI Host Adapter or NICChecking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet portsChecking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet ExplorerUse Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLogDiagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotifyRouteDisplay IsReservedPing SerialNumberTraceLog TemperatureSNMPTraps TraceLogFilterSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc