ATTO Technology 2700C CLI provides ASCII-based interface, Ready, FCTargets command

Page 42

6.1 CLI provides ASCII-based interface

The command line interface (CLI) provides access to the ATTO iPBridge Services through a set of ASCII commands. CLI commands may be entered while in CLI mode.

iPBridge Services provide configuration and monitoring for the iPBridge. CLI commands may be entered while in CLI mode or on the ExpressNAV interface Advanced CLI page.

•CLI commands are context sensitive and generally follow a standard format

[Get Set] Command [Parameter 1 Parameter 2]

followed by the return or enter key

•CLI commands are case insensitive: you may type all upper or all lower case or a mixture. Upper and lower case in this manual and the help screen are for clarification only.

•Commands generally have three types of operation: get, set and immediate.

•The get form returns the value of a parameter or setting and is an informational command.

Responses to get commands are specified in the Results field for each command, followed by Ready.

•The set form is an action that changes the value of a parameter or configuration setting. It may require a SaveConfiguration command and a restart of the system before it is implemented. The restart can be accomplished as part of the SaveConfiguration command or by using a separate FirmwareRestart command. A number of set commands may be issued before the SaveConfiguration command.

Responses to set commands are either an error message or Ready. *. The asterisk indicates you must use a SaveConfiguration command to finalize the set command. SaveConfiguration will ask if you want to restart the system or not.

•Set commands which do not require a SaveConfiguration command, defined as immediate commands, are immediately executed.

Responses to Immediate commands are either an error message or data results followed by

Ready.

For an example of a typical CLI command and response, see Exhibit 6.1-1 on page 46.

Exhibit 6.1-1 Symbols, typefaces and abbreviations used to indicate functions and elements of the command line interface used in this manual.

Command conventions

Symbol

 

Indicates

Symbol

Indicates

 

 

 

 

 

[

]

Required entry

Boldface words

must be typed as they appear

 

 

 

 

 

<

>

Optional entry

Italicized words

Arguments which must be replaced by

 

 

 

 

whatever they represent

 

 

 

 

 

 

pick one of

mp1

Management port

 

 

 

 

…

Ellipses, repetition of

Dp

Data port (0<= Dp <= 4)

 

 

preceding item

 

 

 

 

 

 

 

\n

 

end of line

fp

Fibre Channel port

 

 

 

 

 

-

 

a range (6 – 9 = 6, 7, 8, 9)

fcidx

index field taken from the most recent

 

 

 

 

FCTargets command

 

 

 

 

 

33

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface optionsCLI commands summary General use commands Maintenance commandsDiagnostic commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyAppendix B Cabling Iii Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserTarget names Default target nodeTarget management Map devices automaticallyChap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolAtto ExpressNAV interface Browser compatibilityOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target ManagementUpdating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsFirmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck iPBridge product versions and update firmware Check host versionsCheck components Checking the LAN/WAN Checking the iSCSI Host Adapter or NICChecking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet portsChecking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet ExplorerUse Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLogDiagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotifyRouteDisplay IsReservedPing SerialNumberTraceLog TemperatureSNMPTraps TraceLogFilterSerial port configuration commands SerialPortBaudRateSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSLoginControl ISCSIWANIPAddressISNSServer Mapping commands Route Product features Appendix a Atto FibreBridge familyAtto iPBridge Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc
Top Page Image Contents