ATTO Technology 2700C operation manual Vi Appendix

Page 69

Standard(s) to which conformity is declared: EN55022, EN50082-1, EN60950

This Declaration will only be valid when this product is used in conjunction with other CE approved devices and when the entire system is tested to the applicable CE standards and found to be compliant.

The ATTO FibreBridge 2700 complies with Directive 2002/95/EC on the

Restriction of the Use of Hazardous Substances in Electrical and Electronic

Equipment (RoHS).

vi Appendix

Image 69

Contents Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Atto ExpressNAV pages TroubleshootingUpdating firmware Alternative interface optionsCLI commands summary General use commands Maintenance commandsDiagnostic commands Fibre Channel configuration commands Serial port configuration commandsEthernet commands ISCSI commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyAppendix B Cabling Iii Page Embedded software features Atto iPBridge 2700 features, benefitsAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionScsi Possible storage ConfigurationsAtto iPBridge 2700R/D Installation instructions Front label side Back connector sideInstallation Atto iPBridge 2700R/D Ethernet interface Atto iPBridge 2700CFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP addressTarget management Default target nodeTarget names Map devices automaticallyManually configure multiple target nodes Automatically configure multiple targetsChap to control access different Chap Multiple target nodesPhysical connections Initiator/Host to Network Mapping default vs. multiple target nodesInstallation mapping Page Installation mapping Create a read only password or username Additional configurationsSet the Real Time Clock Click Time & DateSnmp protocol Set up a Vlan Virtual Local Area NetworkAtto ExpressNAV interface Browser compatibilityOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Firmware Update Bridge ConfigurationAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary stepsFirmware update Inside out method TroubleshootingCheck the Host Event Log Check the event and trace logsExhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devicesCheck iPBridge product versions and update firmware Check host versionsCheck components Checking the iSCSI Host Adapter or NIC Checking the LAN/WANChecking the iSCSI OS driver Performance IssuesChecking the Operating System Checking the iPBridge Ethernet portsChecking applications Checking the Ethernet host adapter or NICChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerUse the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages FCTargets command Command conventions Symbol IndicatesCLI provides ASCII-based interface ReadyCLI Error Messages Command Defaults Example CLI commands summaryRmon Sntp Alternative interfaces CLI General use commands VerboseMode UsernameMaintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TailEventLogDiagnostic commands DumpTraceLog DumpEventLogEmailFromAddress EmailNotifyPing IsReservedRouteDisplay SerialNumberSNMPTraps TemperatureTraceLog TraceLogFilterSerial port configuration commands SerialPortBaudRateSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands ISNSLoginControl ISCSIWANIPAddressISNSServer Mapping commands Route Product features Appendix a Atto FibreBridge familyAtto iPBridge Atto FibreBridge Fibre Channel connections Appendix a CablingEthernet connections Cable length Cable sizeTerm Definition Appendix B GlossaryFCC Standards Radio and Television Interference Appendix C Safety standards and compliancesVi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information