ATTO Technology 2700C operation manual Contents

Page 4

Contents
1 ATTO iPBridge 2700 provides storage options	1
ATTO iPBridge 2700 features, benefits
Embedded software features
Connectivity, infrastructure solutions
1.1 ATTO iPBridge 2700R/D	3
Dimensions
Environment
Power
Ethernet interface
Fibre Channel interface
Serial port
LED indicators
Installation instructions
1.2 ATTO iPBridge 2700C	7
Dimensions
Environment
Power
Ethernet interface
Fibre Channel interface
Serial management header
LED indicators
Installation instructions
2 Configuring the iPBridge	9
Microsoft iSCSI Initiator changes
2.1 Getting an IP address	10
2.2 Target management	11
Target names
Default target node
Map devices automatically
Map devices manually
Multiple target nodes
Automatically configure multiple targets
Manually configure multiple target nodes
2.3 Additional configurations	17
Set the Real Time Clock
Change the current username, password
Create a read only password or username
SNMP protocol
Set up a VLAN: Virtual Local Area Network
3 ATTO ExpressNAV interface	19
Browser compatibility
Open an ExpressNAV session

Image 4

Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Troubleshooting Atto ExpressNAV pagesUpdating firmware Alternative interface optionsMaintenance commands CLI commands summary General use commandsDiagnostic commands Serial port configuration commands Fibre Channel configuration commandsEthernet commands ISCSI commandsAppendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Atto iPBridge 2700 features, benefits Embedded software featuresAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Atto iPBridge 2700C Ethernet interfaceFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserDefault target node Target managementTarget names Map devices automaticallyAutomatically configure multiple targets Manually configure multiple target nodesChap to control access different Chap Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Additional configurations Create a read only password or usernameSet the Real Time Clock Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolBrowser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Bridge Configuration Firmware UpdateAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary stepsFirmware update Troubleshooting Inside out methodCheck the Host Event Log Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck host versions Check iPBridge product versions and update firmwareCheck components Checking the LAN/WAN Checking the iSCSI Host Adapter or NICPerformance Issues Checking the iSCSI OS driverChecking the Operating System Checking the iPBridge Ethernet portsChecking the Ethernet host adapter or NIC Checking applicationsChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerAlternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages Command conventions Symbol Indicates FCTargets commandCLI provides ASCII-based interface ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWriteDefault SNTPServerSpeedWrite TailEventLogDiagnostic commands DumpEventLog DumpTraceLogEmailFromAddress EmailNotifyIsReserved PingRouteDisplay SerialNumberTemperature SNMPTrapsTraceLog TraceLogFilterSerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Appendix a Cabling Fibre Channel connectionsEthernet connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc