ATTO Technology 2700C operation manual Sntp

Page 46

Command	Defaults	Example	Page
RouteDisplay		routedisplay iscsi	54

SaveConfiguration		saveconfiguration restart	39

SerialNumber		get serialnumber	45

SerialPortBaudRate	115200	set serialportbaudrate 19200	47

SerialPortEcho	enabled	get serialportecho	47

SNMPDumpMIB		snmpdumpmib	46

SNMPExtendedTraps	disabled	set snmpextendedtraps enabled	46

SNMPTrapAddress	0.0.0.0 none	set snmptrapaddress 6 192.42.155.155 all	46

SNMPTraps	disabled	set snmptraps enabled	46

SNTP	enabled	get sntp	42

SNTPServer	192.43.244.18	set sntpserver 129.6.15.28	42

SpeedWrite		get speedwrite fc all	9

SpeedWriteDefault	disabled	set speedwritedefault enabled	9

TailEventLog		taileventlog	42, 45, 47

Temperature		get temperature	45

Time		set time 03:32:30	42

TimeZone	EST	set timezone pst	42

TraceLog	disabled	set tracelog enabled	46

TraceLogFilter	disabled	set tracelogfilter all all enabled	46

Username	root	set username Barbara	42, 50

VerboseMode	enabled	set verbosemode disabled	40

VLAN		get VLAN 1	50

Voltage		get voltage	46

WrapEventLog	enabled	set wrapeventlog disabled	46

WrapTraceLog	enabled	set wraptracelog disabled	46

37

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 46

Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface optionsMaintenance commands CLI commands summary General use commandsDiagnostic commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commandsAppendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserTarget names Default target nodeTarget management Map devices automaticallyChap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolBrowser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target ManagementUpdating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsFirmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck host versions Check iPBridge product versions and update firmwareCheck components Checking the LAN/WAN Checking the iSCSI Host Adapter or NICChecking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet portsChecking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet ExplorerUse Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLogDiagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotifyRouteDisplay IsReservedPing SerialNumberTraceLog TemperatureSNMPTraps TraceLogFilterSerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc