ATTO Technology 2700C operation manual Appendix C Safety standards and compliances

Page 68
If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures
• Move the receiving antenna.

Appendix C Safety standards and compliances

The equipment described in this manual generates and uses radio frequency energy. If this equipment is not used in strict accordance with the manufacturer's instruction, it can and may cause interference with radio and television reception. Refer to the Technical Specification sheet available at www.attotech.com for a full list of certifications.

WARNING

Risk of explosion if battery is removed and/or replaced by an incorrect type. Dispose of used batteries in accordance with your local environmental regulations.

No operator serviceable components inside the iPBridge 2700C/R/D.

Do not remove cover of iPBridge 2700R/D. Refer servicing to qualified personnel.

FCC Standards: Radio and Television Interference

WARNING

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide a reasonable protection against such interference when operating in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

• Relocate the bridge with respect to the receiver, or move the bridge away from the receiver.

• Plug the computer into a different outlet so the computer and receiver are on different branch circuits.

• If necessary, consult an ATTO authorized dealer, ATTO Technical Support Staff, or an experienced radio/television technician for additional suggestions.

The booklet How to Identify and Resolve Radio/TV Interference Problems prepared by the Federal Com- munications Commission is a helpful guide. It is available from the US Government printing office, Wash- ington, DC 20402, Stock No. 004-000-00345-4.

Canadian Standards

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

European Standards

Declaration of Conformity

This following statement applies to the ATTO iPBridge.

This device has been tested in the basic operating configuration and found to be compliant with the following European Union standards

Application of Council Directive: 89/336/EEC

v

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Troubleshooting Atto ExpressNAV pagesUpdating firmware Alternative interface optionsDiagnostic commands CLI commands summary General use commandsMaintenance commands Serial port configuration commands Fibre Channel configuration commandsEthernet commands ISCSI commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Atto iPBridge 2700 features, benefits Embedded software featuresAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Atto iPBridge 2700C Ethernet interfaceFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserDefault target node Target managementTarget names Map devices automaticallyAutomatically configure multiple targets Manually configure multiple target nodesChap to control access different Chap Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Additional configurations Create a read only password or usernameSet the Real Time Clock Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Bridge Configuration Firmware UpdateAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary stepsFirmware update Troubleshooting Inside out methodCheck the Host Event Log Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the LAN/WAN Checking the iSCSI Host Adapter or NICPerformance Issues Checking the iSCSI OS driverChecking the Operating System Checking the iPBridge Ethernet portsChecking the Ethernet host adapter or NIC Checking applicationsChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerAlternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages Command conventions Symbol Indicates FCTargets commandCLI provides ASCII-based interface ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWriteDefault SNTPServerSpeedWrite TailEventLogDiagnostic commands DumpEventLog DumpTraceLogEmailFromAddress EmailNotifyIsReserved PingRouteDisplay SerialNumberTemperature SNMPTrapsTraceLog TraceLogFilterSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Appendix a Cabling Fibre Channel connectionsEthernet connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc
Top Page Image Contents