ATTO Technology 2700C operation manual Atto FibreBridge

Page 65

ATTO FibreBridge

	Product features	1180E/D	1290E	2300E/R/D	2350C	2390C/R/D	2400C/R/D
Number of FC ports		1	1	1	1	1	2
FC interface		DB9/SC	SFP	SFP	SFP	SFP	SFP
FC data rate		1-GB	2-Gb	2-Gb	2-Gb	4-Gb	4-Gb
Number of SCSI ports		1	2	2	2	2	2
SCSI interface		LVD/SE	LVD/SE	LVD/SE	LVD/SE	LVD/SE	LVD/SE
							VHDCI
Max. data transfer rate		72	160	185	195	280	440
(MB/sec.)

Available configurations		Board	Board	Board	cPCI Board	cPCI Board	cPCI Board
		(Embedded)	(Embedded)	(Embedded)	(Embedded)	(Embedded)	(Embedded)
		Desktop		Rackmount		Desktop	Desktop
				Desktop		Rackmount	Rackmount

Full duplex data transfers		Yes	Yes	Yes	Yes	Yes	Yes
Supports		Yes	Yes	Yes	Yes	No	No
•	Class 2 transfers	Yes	Yes	Yes	Yes	No	No
•	Class 3 transfers	Yes	Yes	Yes	Yes	Yes	Yes
•	intermix transfers	No	Yes	Yes	Yes	No	No
•	direct fabric connect	Yes	Yes	Yes	Yes	Yes	Yes
•	error recovery	Yes	Yes	Yes	Yes	Yes	Yes
Bridge management
available
•	Serial	Yes	Yes	Yes	Yes	Yes	Yes
•	Ethernet	No	Yes	Yes	Yes	Yes	Yes
•	In-band	Yes	Yes	Yes	Yes	Yes	Yes

Serverless backup		Yes	Yes	Yes	Yes	No	No
Virtual Device		No	No	No	No	Yes	Yes
Architecture (VDA
Port failover		No	No	No	No	No	Yes
Diagnostics		Standard	Standard	Standard	Advanced	Advanced	Advanced
ExpressNAV web		No	Yes	Yes	Yes	Yes	Yes
management

ii

Image 65

Contents Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Atto ExpressNAV pages TroubleshootingUpdating firmware Alternative interface optionsDiagnostic commands CLI commands summary General use commandsMaintenance commands Fibre Channel configuration commands Serial port configuration commandsEthernet commands ISCSI commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Embedded software features Atto iPBridge 2700 features, benefitsAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionScsi Possible storage ConfigurationsAtto iPBridge 2700R/D Installation instructions Front label side Back connector sideInstallation Atto iPBridge 2700R/D Ethernet interface Atto iPBridge 2700CFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP addressTarget management Default target nodeTarget names Map devices automaticallyManually configure multiple target nodes Automatically configure multiple targetsChap to control access different Chap Multiple target nodesPhysical connections Initiator/Host to Network Mapping default vs. multiple target nodesInstallation mapping Page Installation mapping Create a read only password or username Additional configurationsSet the Real Time Clock Click Time & DateSnmp protocol Set up a Vlan Virtual Local Area NetworkOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Firmware Update Bridge ConfigurationAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary stepsFirmware update Inside out method TroubleshootingCheck the Host Event Log Check the event and trace logsExhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devicesCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the iSCSI Host Adapter or NIC Checking the LAN/WANChecking the iSCSI OS driver Performance IssuesChecking the Operating System Checking the iPBridge Ethernet portsChecking applications Checking the Ethernet host adapter or NICChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerUse the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages FCTargets command Command conventions Symbol IndicatesCLI provides ASCII-based interface ReadyCLI Error Messages Command Defaults Example CLI commands summaryRmon Sntp Alternative interfaces CLI General use commands VerboseMode UsernameMaintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TailEventLogDiagnostic commands DumpTraceLog DumpEventLogEmailFromAddress EmailNotifyPing IsReservedRouteDisplay SerialNumberSNMPTraps TemperatureTraceLog TraceLogFilterSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Fibre Channel connections Appendix a CablingEthernet connections Cable length Cable sizeTerm Definition Appendix B GlossaryFCC Standards Radio and Television Interference Appendix C Safety standards and compliancesVi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information