ATTO Technology 2700C operation manual Maintenance commands

Page 50

6.1.3 Maintenance commands

The CLI commands outlined in this chapter may be used to get information or perform functions which are used in a variety of situations with the ATTO iPBridge.

Date

Sets the date for the iPBridge if SNTP has been disabled or is not available.

Set syntax: set Date [MM] / [DD] / [YYYY]

Requires a SaveConfiguration command

Get syntax: get Date

FirmwareRestart

Causes the iPBridge to reboot, then re-initialize its firmware.

Immediate command: FirmwareRestart

MaxOpTemp

Establishes/reports the maximum enclosure temperature alarm in degrees Celsius. If the temperature of the iPBridge rises above the maximum MaxOpTemp, thermal control event handling occurs.

Valid entries are between 55 and 70 degrees C

Default: 70

Set syntax: set MaxOpTemp [55-70]

Requires a SaveConfiguration command

Get syntax: get MaxOpTemp

OpTempWarn

Controls the number of degrees in Celsius before a thermal control event handling occurs. Warnings will be made via system log entries. Valid entries are between 0 and 15 degrees

Default: 5

Set syntax: set OpTempWarn [0-15]

Requires a SaveConfiguration command

Get syntax: get OpTempWarn

Password

RestoreConfiguration default sets the password to the default value

Passwords are case sensitive, 1-32 characters with no spaces

When the password is all 0s, TCP/IP and ftp do not validate the password and MD5 authentication are disabled.

Default: Password

Set syntax: set Password

Requires a SaveConfiguration command

MinOpTemp

Establishes/reports the minimum enclosure temperature alarm in degrees Celsius. If the temperature of the iPBridge falls below the minimum MinOpTemp, thermal control event handling occurs. Valid entries are between 0 and 15 degrees

Default: 0

Set syntax: set MinOpTemp [0-15]

Requires a SaveConfiguration command

Get syntax: get MinOpTemp

Reserve

Reservation of the iPBridge is implicit: once the configuration image is changed by any user of services, the iPBridge becomes RESERVED. Executing a SaveConfiguration or\ Restore configuration RELEASES the iPBridge so that other services users may access it. When iPBridge services interface is RESERVED, set commands from other users are unavailable.

At least one interface must always have access to the iPBridge.

Immediate command: Reserve

RestoreConfiguration

Restores configuration to either the default configuration or the configuration last saved into non-volatile memory. The saved option will undo any changes made since the last save.

Immediate command: RestoreConfiguration [Default

Saved]

41

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface optionsDiagnostic commands CLI commands summary General use commandsMaintenance commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserTarget names Default target nodeTarget management Map devices automaticallyChap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target ManagementUpdating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsFirmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the LAN/WAN Checking the iSCSI Host Adapter or NICChecking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet portsChecking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet ExplorerUse Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLogDiagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotifyRouteDisplay IsReservedPing SerialNumberTraceLog TemperatureSNMPTraps TraceLogFilterSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc
Top Page Image Contents