ATTO Technology 2700C operation manual ISCSIWANIPAddress, ISNSLoginControl, ISNSServer

Page 61

iSCSIWANIPAddress

Sets the IP address reported from the sendtargets command. Setting the address to 0.0.0.0 will cause the unit to report the LAN IP address.

Set syntax: set iSCSIWANIPAddress [dp[n] all] [xxx.xxx.xxx.xxx]

Get syntax: get iSCSIWANIPAddress [dp[n] all]

iSNSLoginControl

Specifies whether the iPBridge will delegate its access control/authorization to an iSNS server.

Note: iSNSLoginControl cannot be used with AccessControl

Default: disabled

Set syntax: set iSNSLoginControl [enabled disabled] Requires a SaveConfiguration command

Get syntax: get iSNSLoginControl

iSNSServer

Specifies whether the IP address of a valid iSNS server from which the iPBridge will attempt iSCSI initiator discovery. Setting to 0.0.0.0 will disable iSNS server lookup.

Default: 0.0.0.0

Set syntax: set iSNSServer [xxx.xxx.xxx.xxx] Requires a SaveConfiguration command Get syntax: get iSNSServer

52 Interfaces: CLI

Image 61

Contents Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Atto ExpressNAV pages TroubleshootingUpdating firmware Alternative interface optionsMaintenance commands CLI commands summary General use commandsDiagnostic commands Fibre Channel configuration commands Serial port configuration commandsEthernet commands ISCSI commandsAppendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Embedded software features Atto iPBridge 2700 features, benefitsAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionScsi Possible storage ConfigurationsAtto iPBridge 2700R/D Installation instructions Front label side Back connector sideInstallation Atto iPBridge 2700R/D Ethernet interface Atto iPBridge 2700CFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP addressTarget management Default target nodeTarget names Map devices automaticallyManually configure multiple target nodes Automatically configure multiple targetsChap to control access different Chap Multiple target nodesPhysical connections Initiator/Host to Network Mapping default vs. multiple target nodesInstallation mapping Page Installation mapping Create a read only password or username Additional configurationsSet the Real Time Clock Click Time & DateSnmp protocol Set up a Vlan Virtual Local Area NetworkBrowser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Firmware Update Bridge ConfigurationAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary stepsFirmware update Inside out method TroubleshootingCheck the Host Event Log Check the event and trace logsExhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devicesCheck host versions Check iPBridge product versions and update firmwareCheck components Checking the iSCSI Host Adapter or NIC Checking the LAN/WANChecking the iSCSI OS driver Performance IssuesChecking the Operating System Checking the iPBridge Ethernet portsChecking applications Checking the Ethernet host adapter or NICChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerUse the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages FCTargets command Command conventions Symbol IndicatesCLI provides ASCII-based interface ReadyCLI Error Messages Command Defaults Example CLI commands summaryRmon Sntp Alternative interfaces CLI General use commands VerboseMode UsernameMaintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TailEventLogDiagnostic commands DumpTraceLog DumpEventLogEmailFromAddress EmailNotifyPing IsReservedRouteDisplay SerialNumberSNMPTraps TemperatureTraceLog TraceLogFilterSerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Fibre Channel connections Appendix a CablingEthernet connections Cable length Cable sizeTerm Definition Appendix B GlossaryFCC Standards Radio and Television Interference Appendix C Safety standards and compliancesVi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information