ATTO Technology 2700C Appendix E Warranty, contact information, Contact Atto Technology, Inc

Page 71

Appendix E Warranty, contact information

Manufacturer limited warranty Manufacturer warrants to the original purchaser of this product that it will be free from defects in material and workmanship as described in the ATTO Technology website, www.attotech.com. Manufacturer liability shall be limited to replacing or repairing, at its option, any defective product. There will be no charge for parts or labor should Manufacturer determine that this product is defective.

Products which have been subject to abuse, misuse, alteration, neglected, or have been serviced, repaired or installed by unauthorized personnel shall not be covered under this warranty provision. Damage resulting from incorrect connection or an inappropriate application of this product shall not be the responsibility of Manufacturer. Manufacturer’s liability is limited to Manufacturer’s product(s); damage to other equipment connected to Manufacturer’s product(s) will be the customer’s responsibility.

This warranty is made in lieu of any other warranty, express or implied. Manufacturer disclaims any implied warranties of merchantability or fitness for a particular purpose. Manufacturer’s responsibility to repair or replace a defective product is the sole and exclusive

remedy provided to the customer for breech of this warranty. Manufacturer will not be liable for any indirect, special, incidental, or consequential damages irrespective of whether Manufacturer has advance notice of the possibility of such damages. No Manufacturer dealer, agent or employee is authorized to make any modification, extension or addition to this warranty.

Contact ATTO Technology, Inc.

Customer service, sales and technical support are available by phone Monday through Friday, 8 a.m. to 5 p.m EST., or by fax and web site 24- hours a day.

ATTO Technology, Inc.

155 CrossPoint Parkway

Amherst, New York 14068

(716)691-1999 • voice

(716)691-9353 • fax http://www.attotech.com

ATTO Technology can also be reached via e-mail at the following addresses:

Sales Support:	sls@attotech.com
Technical Support:	techsupp@attotech.com

viii Appendix

Image 71

Contents Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Alternative interface options TroubleshootingAtto ExpressNAV pages Updating firmwareDiagnostic commands CLI commands summary General use commandsMaintenance commands ISCSI commands Serial port configuration commandsFibre Channel configuration commands Ethernet commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Gigabit Ethernet GbE a transmission Atto iPBridge 2700 features, benefitsEmbedded software features Atto iPBridge 2700 provides storage optionsScsi Possible storage ConfigurationsAtto iPBridge 2700R/D Installation instructions Front label side Back connector sideInstallation Atto iPBridge 2700R/D Serial management header Atto iPBridge 2700CEthernet interface Fibre Channel interfaceFaceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP addressMap devices automatically Default target nodeTarget management Target namesMultiple target nodes Automatically configure multiple targetsManually configure multiple target nodes Chap to control access different ChapPhysical connections Initiator/Host to Network Mapping default vs. multiple target nodesInstallation mapping Page Installation mapping Click Time & Date Additional configurationsCreate a read only password or username Set the Real Time ClockSnmp protocol Set up a Vlan Virtual Local Area NetworkOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Manual Target Management iSCSI Target Management Bridge ConfigurationFirmware Update Advanced CLI ConfigurationPreliminary steps Using Atto ExpressNAVUsing FTP over GbE Updating firmwareFirmware update Check the event and trace logs TroubleshootingInside out method Check the Host Event LogExhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devicesCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the iSCSI Host Adapter or NIC Checking the LAN/WANChecking the iPBridge Ethernet ports Performance IssuesChecking the iSCSI OS driver Checking the Operating SystemOptimizing Atto ExpressNAV in Internet Explorer Checking the Ethernet host adapter or NICChecking applications Checking the host systemType iPBridge in the New Connection dialog box Alternative interface optionsUse the serial port or header Use TelnetExhibit 6.0-1 Start up messages Ready Command conventions Symbol IndicatesFCTargets command CLI provides ASCII-based interfaceCLI Error Messages Command Defaults Example CLI commands summaryRmon Sntp Alternative interfaces CLI General use commands VerboseMode UsernameMaintenance commands TailEventLog SpeedWriteDefaultSNTPServer SpeedWriteDiagnostic commands EmailNotify DumpEventLogDumpTraceLog EmailFromAddressSerialNumber IsReservedPing RouteDisplayTraceLogFilter TemperatureSNMPTraps TraceLogSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Cable length Cable size Appendix a CablingFibre Channel connections Ethernet connectionsTerm Definition Appendix B GlossaryFCC Standards Radio and Television Interference Appendix C Safety standards and compliancesVi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information