ATTO Technology 2700C operation manual Physical connections Initiator/Host to Network

Page 22

Exhibit 2.2-1 Target node configurations

Physical connections Initiator/Host to Network

Network to iPBridge Ethernet port iPBridge SCSI port to SCSI device

Server 1

Ethernet
Network	Bridge SN	000123
	Bridge SN	000123
	IP Address: 10.0.3.0
	(1 IP Address for each Ethernet port)		SCSI device
			SCSI device

Server 2

Mapping: default vs. multiple target nodes

SCSI device configuration

Default Target node

Lun 0 Bridge SN 000123

Lun 1

Tape 0

Lun 2

Tape 1

Lun 3

Tape 2

Lun 4

Tape 3

Lun 5

Media Chgr

Node 0

iqn. 1995 - 12. com. attotech : ipbridge :sn- ipb 2700000123

SCSI device configuration

Multiple Target nodes

Lun 0 Bridge SN 000123

Lun 1

Tape 0

Lun 2

Tape 1

Lun 3

Media Chgr

Lun 0 Bridge SN 000123

Lun 1

Media Chgr

: Lun 2

Tape 2

Lun 3

Tape 3

Lun 0 Bridge SN 000123

Node 0

iqn. 1995-12. com. attotech: ipbridge:sn- ipb 2700000123-dev0

Node 1

iqn. 1995-12.com. attotech: ipbridge:sn- ipb2700000123-dev1

Default Node iqn1993-12.com.attotech ipbridgesn-ipb2700000123

13

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 22

Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface optionsMaintenance commands CLI commands summary General use commandsDiagnostic commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commandsAppendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserTarget names Default target nodeTarget management Map devices automaticallyChap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolBrowser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target ManagementUpdating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsFirmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck host versions Check iPBridge product versions and update firmwareCheck components Checking the LAN/WAN Checking the iSCSI Host Adapter or NICChecking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet portsChecking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet ExplorerUse Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLogDiagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotifyRouteDisplay IsReservedPing SerialNumberTraceLog TemperatureSNMPTraps TraceLogFilterSerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc