ATTO Technology 2700C Serial port configuration commands, SerialPortBaudRate, SerialPortEcho

Page 56

6.1.5 Serial port configuration commands

The ATTO iPBridgeserial ports or serial headers are configured with default settings but may be customized to your specifications using the CLI commands in this section.

SerialPortBaudRate

Configures/reports the baud rate for the iPBridge RS-232 serial port or serial header. The number of data bits per character is fixed at 8 with no parity. Choices are 2400, 9600, 19200, 38400, 57600 and 115200.

Default: 115200

Set syntax: set SerialPortBaudRate [2400 9600 19200 38400 57600 115200]

Requires a SaveConfiguration command Get syntax: get SerialPortBaudRate

SerialPortEcho

Enables/disables/reports the echoing of keyboard input. When enabled, all non-control character keyboard input is output to the display.Local ASCII terminal (or terminal emulator) echo settings should be set to disabled while using SerialPortEcho enabled

Default: enabled

Set syntax: set SerialPortEcho [enabled disabled] Requires a SaveConfiguration Restart command Get syntax: get SerialPortEcho

TailEventLog

Displays new events to the terminal during a serial or

Telnet session. Press <ESC> to exit tail mode.

Immediate command: TailEventLog

47

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 56

Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Troubleshooting Atto ExpressNAV pagesUpdating firmware Alternative interface optionsDiagnostic commands CLI commands summary General use commandsMaintenance commands Serial port configuration commands Fibre Channel configuration commandsEthernet commands ISCSI commandsAppendix B Cabling Iii Mapping commandsAppendix a Atto iPBridge, FibreBridge family Page Atto iPBridge 2700 features, benefits Embedded software featuresAtto iPBridge 2700 provides storage options Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Atto iPBridge 2700C Ethernet interfaceFibre Channel interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserDefault target node Target managementTarget names Map devices automaticallyAutomatically configure multiple targets Manually configure multiple target nodesChap to control access different Chap Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Additional configurations Create a read only password or usernameSet the Real Time Clock Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolOpen an ExpressNAV session Atto ExpressNAV interfaceBrowser compatibility Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Bridge Configuration Firmware UpdateAdvanced CLI Configuration Manual Target Management iSCSI Target ManagementUsing Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary stepsFirmware update Troubleshooting Inside out methodCheck the Host Event Log Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck components Check iPBridge product versions and update firmwareCheck host versions Checking the LAN/WAN Checking the iSCSI Host Adapter or NICPerformance Issues Checking the iSCSI OS driverChecking the Operating System Checking the iPBridge Ethernet portsChecking the Ethernet host adapter or NIC Checking applicationsChecking the host system Optimizing Atto ExpressNAV in Internet ExplorerAlternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages Command conventions Symbol Indicates FCTargets commandCLI provides ASCII-based interface ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWriteDefault SNTPServerSpeedWrite TailEventLogDiagnostic commands DumpEventLog DumpTraceLogEmailFromAddress EmailNotifyIsReserved PingRouteDisplay SerialNumberTemperature SNMPTrapsTraceLog TraceLogFilterSerialPortEcho Serial port configuration commandsSerialPortBaudRate Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISNSServer ISNSLoginControlISCSIWANIPAddress Mapping commands Route Atto iPBridge Product featuresAppendix a Atto FibreBridge family Atto FibreBridge Appendix a Cabling Fibre Channel connectionsEthernet connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc