ATTO Technology 2700C operation manual Appendix D Atto accessories

Page 70

Appendix D ATTO accessories

The following accessories are available through ATTO Technology. Contact an ATTO Technology authorized sales representative to order.

iSCSI Bridge board-level models

ATTO iPBridge 2700C

IPBR-2700-C00 4 Gigabit Ethernet by 2 4-Gb Fibre Channel

ATTO iPBridge 2500C

IPBR-2500-C00 3 Gigabit Ethernet by 2 LVD SCSI

ATTO iPBridge 1500E

IPBR-1500-E00 1 Gigabit Ethernet by 1 LVD SCSI, up to 37 MB/sec.

ATTO iPBridge 1550E

IPBR-1550-E00 1 Gigabit Ethernet by 1 LVD SCSI, up to 100 MB/sec.

iSCSI Bridge desktop models & desktop models with rackmount kits

ATTO iPBridge 2700R/D

IPBR-2700-D00 4 Gigabit Ethernet by 2 Gb Fibre Channel

ATTO iPBridge 2500R/D

IPBR-2500-D00 3 Gigabit Ethernet by 2 LVD SCSI

ATTO iPBridge 1500D

IPBR-1500-D00 1 Gigabit Ethernet by 1 LVD SCSI 1, up to 37 MB/sec.

ATTO iPBridge 1550D

IPBR-1550-D00 1 Gigabit Ethernet by 1 LVD SCSI 1, up to 100 MB/sec.

NDMP Bridge models

ATTO iPBridge 2500

IPBR-2500-CN0	3	Gigabit Ethernet by 2	LVD SCSI (board)
IPBR-2500-DN0	3	Gigabit Ethernet by 2	LVD SCSI (desktop)

Cables

CBL-F68R-681 CBL-HD68-681 CBL-LCLC-003 CBL-LCLC-010 CBL-LCSC-003 CBL-LCSC-010

SCSI, Internal Ribbon, 68pin “P”/68pin “P”-0.5m SCSI, External, HD68 to HD68, U320-rated, 1m Fibre Channel, Optical, LC to LC, 3m.

Fibre Channel, Optical, LC to LC, 10m. Fibre Channel, Optical, LC to SC, 3m. Fibre Channel, Optical, LC to SC, 10m.

Accessories

TERM-V68E-002 Terminator, LVD SCSI, VHDCI, Active 125

ADAP- 50AF- 68P* Adapter, SCSI, 50pin “A” Female to 68pin “P” Female 60 SFP2-0000-000 Adapter, 2-Gigabit Fibre Channel, Short Wave Optical, SFP LC SFP4-0000-000 Adapter, 4-Gigabit Fibre Channel, Short Wave Optical, SFP LC

Cables: RS232

CBL-0911-001 Cable, Serial RS232, RJ11 to DB9, 10 ft.

vii

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 70

Contents Atto iPBridge 2700C/R/D Atto Technology, IncPage Page Contents Updating firmware TroubleshootingAtto ExpressNAV pages Alternative interface optionsMaintenance commands CLI commands summary General use commandsDiagnostic commands Ethernet commands Serial port configuration commandsFibre Channel configuration commands ISCSI commandsAppendix a Atto iPBridge, FibreBridge family Mapping commandsAppendix B Cabling Iii Page Atto iPBridge 2700 provides storage options Atto iPBridge 2700 features, benefitsEmbedded software features Gigabit Ethernet GbE a transmissionPossible storage Configurations ScsiAtto iPBridge 2700R/D Installation instructions Back connector side Front label sideInstallation Atto iPBridge 2700R/D Fibre Channel interface Atto iPBridge 2700CEthernet interface Serial management headerFaceplate side Power side Configuring the iPBridge Getting an IP address Click Launch BrowserTarget names Default target nodeTarget management Map devices automaticallyChap to control access different Chap Automatically configure multiple targetsManually configure multiple target nodes Multiple target nodesMapping default vs. multiple target nodes Physical connections Initiator/Host to NetworkInstallation mapping Page Installation mapping Set the Real Time Clock Additional configurationsCreate a read only password or username Click Time & DateSet up a Vlan Virtual Local Area Network Snmp protocolBrowser compatibility Atto ExpressNAV interfaceOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Advanced CLI Configuration Bridge ConfigurationFirmware Update Manual Target Management iSCSI Target ManagementUpdating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsFirmware update Check the Host Event Log TroubleshootingInside out method Check the event and trace logsCheck for problems on attached devices Exhibit 5.0-1 iPBridge 2700C faceplateCheck host versions Check iPBridge product versions and update firmwareCheck components Checking the LAN/WAN Checking the iSCSI Host Adapter or NICChecking the Operating System Performance IssuesChecking the iSCSI OS driver Checking the iPBridge Ethernet portsChecking the host system Checking the Ethernet host adapter or NICChecking applications Optimizing Atto ExpressNAV in Internet ExplorerUse Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 6.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol IndicatesFCTargets command ReadyCLI Error Messages CLI commands summary Command Defaults ExampleRmon Sntp Alternative interfaces CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TailEventLogDiagnostic commands EmailFromAddress DumpEventLogDumpTraceLog EmailNotifyRouteDisplay IsReservedPing SerialNumberTraceLog TemperatureSNMPTraps TraceLogFilterSerialPortBaudRate Serial port configuration commandsSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyPassword ReadOnlyUsernameISCSI commands ISCSIWANIPAddress ISNSLoginControlISNSServer Mapping commands Route Appendix a Atto FibreBridge family Product featuresAtto iPBridge Atto FibreBridge Ethernet connections Appendix a CablingFibre Channel connections Cable length Cable sizeAppendix B Glossary Term DefinitionAppendix C Safety standards and compliances FCC Standards Radio and Television InterferenceVi Appendix Appendix D Atto accessories Appendix E Warranty, contact information Contact Atto Technology, Inc