ATTO Technology 2700C operation manual RouteDisplay

Page 63

Route

Assigns a host protocol address to a target destination device.

Immediate command: Route [iSCSI] [defaultTarget Name] [lun] [FC [fp]fcidx] BridgeDelete]

RouteDisplay

Displays a combined list of host protocol addresses to target destination device mappings.

Immediate command: RouteDisplay iSCSI [default <lun>Target Name <lun>]

54 Interfaces: CLI

Image 63

Contents Atto Technology, Inc Atto iPBridge 2700C/R/DPage Page Contents Alternative interface options TroubleshootingAtto ExpressNAV pages Updating firmwareCLI commands summary General use commands Maintenance commandsDiagnostic commands ISCSI commands Serial port configuration commandsFibre Channel configuration commands Ethernet commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyAppendix B Cabling Iii Page Gigabit Ethernet GbE a transmission Atto iPBridge 2700 features, benefitsEmbedded software features Atto iPBridge 2700 provides storage optionsScsi Possible storage ConfigurationsAtto iPBridge 2700R/D Installation instructions Front label side Back connector sideInstallation Atto iPBridge 2700R/D Serial management header Atto iPBridge 2700CEthernet interface Fibre Channel interfaceFaceplate side Power side Configuring the iPBridge Click Launch Browser Getting an IP addressMap devices automatically Default target nodeTarget management Target namesMultiple target nodes Automatically configure multiple targetsManually configure multiple target nodes Chap to control access different ChapPhysical connections Initiator/Host to Network Mapping default vs. multiple target nodesInstallation mapping Page Installation mapping Click Time & Date Additional configurationsCreate a read only password or username Set the Real Time ClockSnmp protocol Set up a Vlan Virtual Local Area NetworkAtto ExpressNAV interface Browser compatibilityOpen an ExpressNAV session Exhibit 3.0-1 An ExpressNAV Atto ExpressNAV pages Manual Target Management iSCSI Target Management Bridge ConfigurationFirmware Update Advanced CLI ConfigurationPreliminary steps Using Atto ExpressNAVUsing FTP over GbE Updating firmwareFirmware update Check the event and trace logs TroubleshootingInside out method Check the Host Event LogExhibit 5.0-1 iPBridge 2700C faceplate Check for problems on attached devicesCheck iPBridge product versions and update firmware Check host versionsCheck components Checking the iSCSI Host Adapter or NIC Checking the LAN/WANChecking the iPBridge Ethernet ports Performance IssuesChecking the iSCSI OS driver Checking the Operating SystemOptimizing Atto ExpressNAV in Internet Explorer Checking the Ethernet host adapter or NICChecking applications Checking the host systemType iPBridge in the New Connection dialog box Alternative interface optionsUse the serial port or header Use TelnetExhibit 6.0-1 Start up messages Ready Command conventions Symbol IndicatesFCTargets command CLI provides ASCII-based interfaceCLI Error Messages Command Defaults Example CLI commands summaryRmon Sntp Alternative interfaces CLI General use commands VerboseMode UsernameMaintenance commands TailEventLog SpeedWriteDefaultSNTPServer SpeedWriteDiagnostic commands EmailNotify DumpEventLogDumpTraceLog EmailFromAddressSerialNumber IsReservedPing RouteDisplayTraceLogFilter TemperatureSNMPTraps TraceLogSerial port configuration commands SerialPortBaudRateSerialPortEcho Fibre Channel configuration commands Ethernet commands ReadOnlyUsername ReadOnlyPasswordISCSI commands ISNSLoginControl ISCSIWANIPAddressISNSServer Mapping commands Route Product features Appendix a Atto FibreBridge familyAtto iPBridge Atto FibreBridge Cable length Cable size Appendix a CablingFibre Channel connections Ethernet connectionsTerm Definition Appendix B GlossaryFCC Standards Radio and Television Interference Appendix C Safety standards and compliancesVi Appendix Appendix D Atto accessories Contact Atto Technology, Inc Appendix E Warranty, contact information