Philips CDR 760 manual Fixing Problems, Troubleshooting, Diagnostic program

Page 20

FIXING PROBLEMS

English

tray.

Troubleshooting

If you think your CD recorder is defective, it is wise to check this list first and run the diagnostic program. Maybe you have forgotten a simple step.

Warning!

Under no circumstances should you attempt to repair the CD recorder yourself as this will invalidate the guarantee.

SYMPTOM: • SOLUTION:

No power • check to ensure that the ON/OFF button is on

•check to ensure that the power cable is plugged in correctly

•switch the recorder OFF and then immediately back ON

Auto track does not work

•check to ensure that auto track is selected.

•check to ensure that there are 3 seconds silence in between the tracks (analogue recording only)

•check to ensure that the source is a consumer source with the digital output according the IEC audio standard.

No sound • check the audio connections

•if using an amplifier, try using a different source

Amplifier sound is distorted

•check to ensure that the CD recorder analogue output is not connected to the amplifier Phono input.

Play will not start

•check to ensure that the label of the CD is facing up

•clean the disc

•check to ensure that the disc is not defective by trying another disc

Remote control does not work

•point the remote control directly at the CD recorder

•check the batteries and replace if necessary

•select the right source first

Will not record

•clean the disc.

•check to ensure that CD-RW is not finalized

•check to ensure that the disc is recordable and replace if necessary

•the disc is not an AUDIO disc

•wrong input source selected.

Analog recording is distorted

•make sure the recording level is correct

20 second pause between recordings

•see synchronized digital recording (CD-SYNC) p. 8

Player does not react

•switch the ON/OFF button on the front of the player off and back then on

SERVICE on display after switching on •try switching off and on again

RECOVER on display

•a power failure has occurred during recording; the CD recorder is attempting to repair the disc.

•if RC-DISC then appears on the display, the disc cannot be recorded further, and cannot be finalized. However, it can be played on a CD recorder.

•on a CD-RW disc, the track being recorded is lost, but further recording and finalization can still be done.

•if OPC FAIL appears, no further recording is possible. You can still use the disc as a CD on this recorder.

Diagnostic program

If the malfunction continues, perform the Diagnostic Program:

1Switch the recorder off using ON/OFF.

2Simultaneously press PLAY and STOP and switch the recorder back on using ON/OFF.

➜The display will now indicate BUSY and after a few minutes, the message will change to ERROR or

PASSED

•If the ERROR message appears, your recorder is defective and needs to be repaired. Consult your supplier or call the Philips Consumer Line to find the nearest service center. The number of the Consumer Line can be found in the guarantee booklet.

•If the PASSED message appears, you may be misinterpreting the user instructions or using an inappropriate disc, or there may be a mechanical defect or an incorrect connection. Carefully read the user instructions once again; and if necessary contact your supplier.

•If you cannot solve the problem, contact to the nearest service center.

3Switch off the recorder using ON/OFF to exit from the Diagnostic Program.

18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents CDR 760 CD recorder Important Safety Instructions English Français Español ContentsEnspañol Français English Type General InformationSet complies with the FCC-Rules, Part 15 and with 21 CFR Limited Warranty CD-R PlayerTechnical information English Table of contentsWelcome Discs for recording Maintenance English AccessoriesDiscs for playback CD-Audio Recordable CD-R discsOperating Buttons and Connections Operating buttons on the front Connections on the backDisplay messages DisplayDisplay explanation Installation Connections generalOptical output of a CD player Digital coaxial connectionsDigital optical connections Press ON/OFF to turn the CD recorder on Power supplySet-up recommendations Remote Control & Inserting Discs Remote control commandsInserting discs Display will indicate the type of disc you have insertedRecording English Remarks about recordingDigital recording unsynchronized Digital unsynchronized Digital synchronized AnalogueSynchronized digital recording CD-SYNC Start digital recordingPreparing for synchronized digital recording Start synchronized digital recordingStop the source Analogue recordingPreparing for analogue recording For CD-RW discs only English Unfinalizing CD-RW discsStart analogue recording Erasing & Playing Erasing CD-RW discsPlaying a CD To erase the last trackPlaying Selecting a track or searchingShuffle play Repeat CD, track or programDiagnostic program Fixing ProblemsTroubleshooting Généralités Table des matièresBienvenue Caractéristiques techniquesDisques destinés à la lecture AccessoiresDisques destinés à l’enregistrement Entretien Français Commandes ET Connexions FrançaisPhones . . . . . . . . . prise pour casque Connexion secteurAfficheur DescriptionGénéralités sur les connexions Utilisez le câble fourni avec l’appareil avec fiches noires Remettez le couvercle en place Conseils d’installationOuvrez le couvercle du compartiment des piles Français Commandes à distance Mise en place des disquesRecherche avant ChargementEnregistrement DIG Coaxial ou DIG Optical s’afficheEnregistrement numérique synchronisé CD-SYNC Démarrage de l’enregistrement numériqueRecord clignote PréparationEnregistrement analogique Arrêtez la sourceDémarrage de l’enregistrement analogique Finalisation disques CD-R et CD-RWAnnulation de la finalisation disques CD-RW Effacement ET Lecture Effacement des disques CD-RWLecture d’un disque compact Pour effacer la dernière plageSélection d’une plage ou recherche Lecture en mode aléatoireLecture Programmation Prog clignote sur l’afficheurAppuyez sur Play pour démarrer la lecture du programme Effacement d’un programmeEN CAS DE Problemes Français DépannageProgramme de diagnostic Remarques Información General IndiceBienvenido Datos técnicosAccesorios Discos para grabación Mantenimiento EnspañolDiscos para reproducción Controles Y Conexiones Controles del panel frontal Conexiones del panel posteriorMensajes de pantalla PantallaDescripción de la pantalla Instalación Conexiones generalesDigital óptica de un reproductor de CD Conexiones digitales coaxialesConexiones digitales ópticas Pulse ON/OFF para encender el grabador de CD Recomendaciones de configuraciónAlimentación Mando a Distancia E Inserción DE Discos Órdenes del mando a distanciaInserción de discos ShuffleGrabación El número de grabaciones del original es ilimitadoGrabación digital sincronizada CD-SYNC Comienzo de grabación digitalPreparación para la grabación digital sincronizada Inicie la grabación digital sincronizadaPreparación para la grabación analógica Grabación analógicaEnspañol Finalización de discos CD-R y CD-RW Rehabilitación de discos CD-RWDetenga la fuente Inicie la grabación analógicaBorrado de discos CD-RW Reproducción de un CDPara borrar la última pista Para borrar todo el discoReproducción Selección de una pista o búsquedaReproducción aleatoria Selección de una pista con el disco paradoBorrado de un programa Repetición de CD, pista o programa ProgramaciónPulse Play para dar comienzo a la reproducción del programa Programa de diagnóstico Detección DE ProblemasEnspañol Solución de problemas
Top Page Image Contents