Tripp Lite SU10KRT3/1X owner manual Specifications, Storage and Service

Page 18

10 – Specifications

Input

 

 

 

 

 

 

 

Voltage Range

Up to 160-280/277-485V AC (3Ø, 4-Wire + Ground, Wye)

 

(160-176/277-305V AC at Load < 75%)

 

 

 

 

Frequency Range

45 to 65 Hz

 

 

 

 

Power Factor

Up to 0.99 at 100% Linear Load

Output

 

 

 

 

 

 

 

Voltage Range

User-Selectable 200/220/230/240V AC (1Ø, 2-Wire + Ground)

 

 

 

 

Voltage Adjustment

±0%; ±1%; ±2%; ±3%

 

 

 

 

Voltage Regulation

±2%

 

 

 

 

Capacity

10 kVA / 7 kW

 

 

 

 

Rated Power Factor

0.8 Lagging

 

 

 

 

Wave Form

Pure Sine Wave, THD <3%

 

 

 

 

Frequency Stability

±0.2% (Free-Running)

 

 

 

 

Frequency Regulation

±1%; ±3%

 

 

 

 

Transfer Time to Battery

0 ms

 

 

 

 

Crest Factor

3:1 Acceptable

 

 

 

 

Efficiency (AC to AC, Normal Mode)

Up to 91%

 

 

 

 

Efficiency (AC to AC, Economy Mode)

Up to 93%

 

 

 

 

Estimated Full Load Runtime

 

 

5 minutes

 

 

 

 

Estimated Half Load Runtime

 

 

14 minutes

 

 

 

 

Physical

 

 

 

 

 

 

 

Dimensions (H x W x D)

135 x 440 x 680 mm (Power Module)

 

 

 

 

Input/Output Connection

Hardwire

 

 

 

 

Unit Weight

28 kg (Power Module)

 

 

 

 

11 – Storage and Service

Storage

First turn the UPS system’s output and utility input breaker OFF, then disconnect the UPS system’s input from the AC utility power source. Next, disconnect all equipment. The UPS system must be stored in a clean, secure environment with a temperature less than 40° C and a relative humidity less than 90% (non-condensing). Note: If the UPS system remains off for an extended period of time, it should be turned on periodically to allow the batteries to recharge. The UPS system should be turned on and the batteries should be recharged at least one uninterrupted 12-hour period every three months in moderate-temperature environments (-15° to 30° C), or every two months in high- temperature environments (30° to 40° C). Failure to recharge the batteries periodically may cause irreversible battery damage.

Service

The UPS system is covered by the limited warranty described in this manual. Extended and on-site warranty options are also available. For more information, call Tripp Lite Customer Service at +1.773.869.1234. If returning the UPS system to Tripp Lite, carefully pack the UPS system using the original packing material that came with the unit. Enclose a letter describing the symptoms of the problem. If the UPS system is within the warranty period, enclose a copy of the sales receipt.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Español FrançaisРусский Location Warnings Important Safety InstructionsIntroduction Connection WarningsWiring Warnings Battery WarningsRear Panel Features UPS System Power Module Rear PanelMounting UPS System Hardware KitPlacement Post Mounting ProcedureMounting Rack Terminal Block Diagram WiringWiring Preparation Tower Mounting ProcedureAC Input/Output Wiring Instructions AC Input and Output 75C Minimum Copper WireElectrical and Cable Data External Battery Pack Connection External battery pack is required to operate the UPS systemStandard Operation Control Panel FeaturesUPS System Power on Buzzer SilenceSymbol Description Control Panel Error CodesLCD Symbols Code DescriptionNormal Mode Startup UPS System Shutdown Battery Mode Startup Cold StartUPS System Settings and Measurements Checking UPS System MeasurementsSettings and Special Functions Changing Default SettingsStart-up Procedure UPS System PlacementInstallation Parallel Redundancy Operation OptionalEPO Connection CommunicationsNetwork Card RS-232 Serial CommunicationsProblem LCD Screen Error Code Possible Solution TroubleshootingUPS Detects Error While in Self-Test Mode To release the UPS system lockService SpecificationsStorage and Service StorageWarranty Limited WarrantyRegulatory Compliance Identification Numbers Apagado del sistema de UPS English Français РусскийDesembalaje Colocación Montaje Rack Montaje Torre Tarjeta de red Puerto EPO Comunicaciones seriales RS-232Advertencias de ubicación IntroducciónInstrucciones de seguridad importantes Advertencias sobre la conexiónAdvertencias sobre las baterías Instrucciones de seguridad importantes continuaciónAdvertencias sobre el cableado Notas sobre las etiquetasCaracterísticas del panel posterior Montaje DesembalajeKit de herramientas del sistema de UPS Colocación Montaje RackProcedimiento después del montaje Montaje Torre Diagrama del bloque de terminalesCableado Preparación para el cableadoDatos eléctricos y de los cables Instrucciones del cableado de entrada/salida de CAEntrada y salida de CA cable de cobre de mínimo 75 ºC Conexión del módulo de baterías externas Funcionamiento estándar Características del panel de control9 10 11 Características del panel de control continuación Códigos de error del panel de controlFuncionamiento estándar continuación Símbolos LCDArranque en modo normal Apagado del sistema de UPS Configuraciones y mediciones del sistema de UPSArranque en modo batería arranque en frío Cómo controlar las mediciones del sistema de UPSConfiguraciones y funciones especiales Cómo cambiar las configuraciones predeterminadasInstalación Funcionamiento con redundancia paralela opcionalColocación del sistema de UPS Procedimiento de arranqueConexión EPO ComunicacionesTarjeta de red Comunicaciones seriales RS-232Resolución de problemas Problema Código de error de pantalla LCD Solución posiblePara liberar el bloqueo del sistema de UPS Almacenamiento EspecificacionesAlmacenamiento y servicio Servicio técnicoGarantía Garantía limitadaCumplimiento de las normas de los números de identificación GarantieCaractéristiques eau de c EnglishAvertissements relatifs à l’emplacement Consignes importantes de sécuritéAvertissements relatifs aux connexions Consignes importantes de sécurité suite Avertissements relatifs aux câblagesAvertissements relatifs aux batteries Caractéristiques du panneau arrière Panneau arrière du module d’alimentation du système ASIDéballage MontageLire la Consignes importantes de sécurité avant le montage Kit matériel système ASIMontage rack Montage suiteMise en place Procédure de montage avec 4 montantsPréparation des câbles CâblageMontage tour Schéma des bornesConsignes de câblage entrée/sortie c.a Câblage suiteDonnées électriques et câbles Entrée et sortie c.a. fil en cuivre minimum 75 CConnexion du pack batterie externe Caractéristiques du panneau de contrôle Mise en sourdine de l’alarmeFonctionnement standard Mise sous tension du système ASIFonctionnement standard suite Symbole LCDSymbole Description Codes d’erreur du panneau de contrôleDémarrage en mode normal Réglages et mesures du système ASI Démarrage en mode batterie démarrage à froidArrêt du système ASI Vérification des mesures du système ASIRéglages et mesures du système ASI suite Réglages et fonctions spécialesModification des réglages par défaut Emplacement du système ASI Fonctionnement en redondance parallèle en optionProcédure de démarrage Communications série RS-232 Carte réseauConnexion EPO Réglages d’interface RS-232Problème Code d’erreur de l’écran LCD Solution possible Résolution des problèmes’ASI détecte une erreur en mode auto-test Pour déverrouiller le système ASIStockage SpécificationsEntretien et stockage RévisionGarantie Garantie limitéeNuméros d’identification de conformité aux règlements English EspañolFrançais Меры предосторожности при выборе места размещения и сборке ВведениеОсновные правила техники безопасности Меры предосторожности при подключении к источнику питанияОсновные правила техники безопасности продолжение Элементы задней панели Условные обозначения на этикеткеЗадняя панель силового модуля системы ИБП Сборка РаспаковкаКомплект крепежа для сборки системы ИБП Размещение Сборка стоечный вариантПроцедура сборки в стойку с 4 опорами Rack Схема блока выводов Электромонтажные работы и подключениеСборка вертикальный вариант Процедура сборки вертикального варианта TowerЭлектромонтажные работы и подключение продолжение Параметры входов/выходов и кабелейИнструкции по монтажу входов/выходов переменного тока Подсоединение внешнего блока аккумуляторных батарей Включение питания системы ИБП Эксплуатация системы в стандартной конфигурацииЭлементы контрольной панели Отключение зуммераКоды ошибок, выдаваемые на контрольную панель Эксплуатация системы в стандартной конфигурации продолжениеЭлементы контрольной панели продолжение Символы, выводимые на ЖК-дисплейЗапуск при работе в нормальном режиме Настройки и значения измеряемых параметров системы ИБП Запуск в батарейном режиме Холодный стартОтключение системы ИБП Проверка измеряемых параметров системы ИБПНастройки и специальные функции Изменение стандартных настроекРазмещение системы ИБП Сборка и установкаПроцедура запуска Порт EPO аварийного отключения питания Возможность использования сетевых подключенийСетевая карта Серийный порт RS-232Диагностика и устранение неисправностей Для разблокировки системы ИБПХранение 10 Технические характеристики11 Хранение и обслуживание Обслуживание12 Гарантия Ограниченная гарантия

SU10KRT3/1X specifications

The Tripp Lite SU10KRT3/1X is a robust and efficient 10kVA UPS (Uninterruptible Power Supply) designed to meet the power management needs of critical electronic equipment. This industrial-grade UPS is ideal for safeguarding servers, telecommunications equipment, and networking hardware, providing the reliability necessary in today's tech-dependent world.

One of the standout features of the SU10KRT3/1X is its ability to deliver pure sine wave output, which ensures that connected devices receive a stable and clean power supply. This is especially crucial for sensitive electronics, including servers and other IT infrastructure components that require a consistent power source to maintain peak performance and operational integrity.

The UPS boasts a comprehensive input voltage range, making it adaptable to various power conditions. With an output power factor of 0.9, the SU10KRT3/1X maximizes the power available for connected devices, providing efficient power usage that ultimately lowers operational costs. This UPS also features an automatic voltage regulation (AVR) system that stabilizes voltage fluctuations, offering an additional layer of protection against surges and brownouts.

Another significant characteristic of the Tripp Lite SU10KRT3/1X is its modular design, featuring hot-swappable batteries that allow for easy maintenance without shutting down connected equipment. This feature minimizes downtime and enhances reliability, ensuring that critical systems remain functional even during maintenance activities.

The LCD display provides real-time status information, including input and output voltage, battery status, and load levels. This user-friendly interface allows IT administrators and technicians to monitor the UPS easily and respond quickly to any potential issues.

Compatibility is another area where the SU10KRT3/1X excels. It is equipped with multiple communication options, including USB, RS-232, and optional SNMP capability, enabling seamless integration with monitoring systems and ensuring effective communication with connected devices.

Tripp Lite has backed the SU10KRT3/1X with a solid warranty and exceptional customer support, assuring users of the product's reliability and performance. As organizations increasingly rely on technology, the SU10KRT3/1X serves as a trustworthy solution for maintaining consistent power availability, ultimately contributing to business continuity and efficiency.
Top Page Image Contents