Network Technologies CS-16/8 operation manual Port Settings, Port settings menu

Page 19

NTI RACK MOUNT CONSOLE TERMINAL WITH CONSOLE SWITCH

FYI: RE: DscTime ( Disconnect Time)

The value shown in the Port list is derived from various sources depending on the type of connection active at the time.

-If a user is logged into a port as just a user, the time shown will be the remaining time based on the user's timeout setting.

-If a user is logged in with administrative privileges and performing administrative tasks, the time will be based on the administrator's timeout setting, not based on the user's timeout setting.

- If two ports are connected to each other, and one port has a lower timeout setting than the other, the lower setting will be shown in the DscTime column and control the connection.

-Press [N] to display port information for ports greater than 16, and then [P] to see the previous page.

-Press [R] to refresh the information displayed

-Press [Esc] or [Spacebar] to return to the Administrator main menu

3.1.3 Port Settings

From the Administrator main menu, press [2]-[x]-[Enter]] where x is the number of the port to display the port settings for.

Figure 10- The Port settings menu

14

Image 19

Contents SERIMUX-TERM-CS-16/8 Trademark Table of Contents 1 VT100, VT220 and Console Ansi Command Guide Table of Figures Multiple RS-232 Emulations FeaturesIntroduction Terminal ConverterConsole Switch DB25M-RJ45F-C DB9F-RJ45F MaterialsFront and Rear Views of SERIMUX-TERM-CS-16 Features and FunctionsRack Mounting Instructions Installation#10-32x3/4 Rack Screws supplied Cage Nuts Supplied RJ45 Male Connector Connect Devices, Hosts, and PowerIEC Power Connector PowercordMonitor Power Up The SERIMUX-TERM-CS-16Connect the Serimux and Terminal to a Network Connect the Monitor and KeyboardGetting Started Setup The TerminalConnect to the Serimux Saving and Exiting SetupF2- Genrl Setup Menu F4- Comm Setup MenuStartup- Accessible host list Serial Control Using the Serimux Console SwitchDefault keypad PIN number is Terminal ControlLogin as the administrator Administrator ControlsPort list displays the status of all ports Port ListPort settings menu Port SettingsSetting Description Value Parity Port serial settingsData bit Stop BitDTR line behavior Flow control CommandInter-character delay Xon or Xoff CharactersFunction Keystroke Modem settingsCopy Port Serial Settings Display serial settings for different port numberPort data buffer Display modem settings for different port numberClear Port data buffer User List User ListUser settings menu User SettingsCopy User Settings Port accessOption Description Local KeyPad PIN Defines the PIN number for Local Advanced SettingsChange administrator password Setting Description ValueFunction Description FirmwareLoad new firmware Save current firmware Serimux is waiting to save its firmware User Controls User Accessible host list screenUser main menu User main menuPort List screen Limited user accessible Port list¾ Port info User Terse modeTerse mode commands ¾ Connect to port ¾ Accessible host list¾ Verbose mode System Reset button¾ User Logout Firmware upload window Firmware UpgradeLast confirmation before firmware update Action from Keypad Reaction of Serimux Login the administratorKeypad Control Functions of the KeypadLogin user to a port Login a user to the administrator main menuConnect 2 host ports Disconnect and logout a userAction from Keypad Disconnect 2 ports Reset Serimux Console Switch to default settingsTo detach a modem How To Setup The Terminal Using the TerminalF2- Genrl Setup Menu F1- Disp Setup MenuChanging The Terminal Operating Parameters F4- Comm Setup Menu F3- Keybd Setup MenuPrinter Printer RCV ON/OFF F5- Misc Setup MenuF7- FKeys SET-UP Definition Setup Menu F6-Tabs SET-UP MenuProgrammable Keys F9- Lan Setup MenuF8- Ansbk SET-UP Menu F10- Colr1 Set-up MenuOption Color Association = OFF/ON Color Setup MenuF11- Colr2 Set-up Menu Attribute = Bold/BlinkPalette Display Attribute Foreground Color Background Color Color PalettesColor Palettes Contd Command Enhanced PC Local Keyboard CommandsWyse Terminal Command GuideCommands Supported in Ascii Personalities SameKey/fkey DEL Native Mode WyseSelect bell volume Stop parity wordMessage CR Sequence DELKey/fkey Sequence Sequence DEL ESC . cursor1Bcolor map ESC a mf attrAttr FcolorLine col ColCcc C Clearing Data Editing ContdSending data Pp bb...bb Print FunctionsCharacter Sets SetVariable Values for Commands Variable Values for Commands Contd Max Maximum Speed LengthLine/Column DefinitionParity Bits Bell VolumeFunction Key Palette Color Pallette1 VT100, VT220 and Console Ansi Command Guide Ansi Command GuideSupported VT100,VT220 and Console Ansi Commands Label assigned Supported VT100, VT220 and Console Ansi Commands, ContdCharacter Set Selection ESC Ps finalCharacter Attribute Supported VT100, VT220 and Console Ansi Commands ContdFinal character Values for Ps aboveEditing Functions Values for Psn in table onClear Key Lock See tables below an on next page for values Kc/hc ST StringShifted function key Values of Fn for Numeric Keypad keys Redefine keys with stringUnshifted function key Key ValueTransmission/Printer Control More Terminal Control CommandsTerminal Resets Auxiliary Keypad ModesKeyboard Language 2 VT52 Command GuideCommand VT52 See table below for values of PsBasic Setup Using Printer Server via Ethernet ConnectionSetup for LPD LPD printing Setup for TftpTftp Printing Hardware Specifications Serimux Hardware Specifications TerminalHardware Information Serial Port Pinouts Pin assignment at Wire Color Standard End Crossed EndCPU-to-RACKMUX Ethernet Crossover Cable Serial Port CablingCable Adapters RJ45 SignalDB25F Mating face of an RJ45 Female Terminal Connector Pin AssignmentsSUB-D Female connector 3 4Administrator Appendix a Serimux Port CharacteristicsDescription Acceptable Value Default Value Appendix B Serimux User and Administrator CharacteristicsIndex Warranty Information