Network Technologies CS-16/8 operation manual System Reset button, ¾ Verbose mode, ¾ User Logout

Page 35

NTI RACK MOUNT CONSOLE TERMINAL WITH CONSOLE SWITCH

¾Verbose mode

Send or type in:

[V] [Enter]

The answer will be: OK [CR][LF]

and the Terse mode will be terminated. The “Accessible host list” or the “User main menu” will be displayed.

¾User Logout

Send or type in:

[L] [Enter]

The answer will be:

OK [CR][LF]

With the next login of the same user, Terse mode will resume.

3.2.5 System Reset button

The “System Reset” button, located on the rear of the RACKMUX (see Figure 25), may be pressed at any time to refresh the SERIMUX without powering it OFF. This might be necessary in the event the SERIMUX should fail to respond to normal commands.

System Reset button

R TECHNOLOGIESNETWORK			MONITOR		SERIAL		PRINTER		PARALLEL
NTI1275 Danner Dr	INCORPORATED
NTI1275 Danner Dr	Tel:330-562-7070
Aurora, OH 44202	Fax:330-562-1999
www.networktechinc.com							12	11		9	8	7
	16		15	14	13		12	11	10	9	8	7	6

TERMINAL-	RESET		ISP
TERMINAL-
10 BASE T
5	4	3	2	1	KEYBOARD
5	4	3	2	1

Rear View of SERIMUX-TERM-CS-16

Figure 25- Location of Restore Defaults button

30

Image 35

Contents SERIMUX-TERM-CS-16/8 Trademark Table of Contents 1 VT100, VT220 and Console Ansi Command Guide Table of Figures Multiple RS-232 Emulations FeaturesIntroduction Terminal ConverterConsole Switch DB25M-RJ45F-C DB9F-RJ45F MaterialsFront and Rear Views of SERIMUX-TERM-CS-16 Features and Functions#10-32x3/4 Rack Screws supplied Cage Nuts Supplied InstallationRack Mounting Instructions RJ45 Male Connector Connect Devices, Hosts, and PowerIEC Power Connector PowercordMonitor Power Up The SERIMUX-TERM-CS-16Connect the Serimux and Terminal to a Network Connect the Monitor and KeyboardGetting Started Setup The TerminalConnect to the Serimux Saving and Exiting SetupF2- Genrl Setup Menu F4- Comm Setup MenuStartup- Accessible host list Serial Control Using the Serimux Console SwitchDefault keypad PIN number is Terminal ControlLogin as the administrator Administrator ControlsPort list displays the status of all ports Port ListPort settings menu Port SettingsSetting Description Value Parity Port serial settingsData bit Stop BitDTR line behavior Flow control CommandInter-character delay Xon or Xoff CharactersFunction Keystroke Modem settingsCopy Port Serial Settings Display serial settings for different port numberClear Port data buffer Display modem settings for different port numberPort data buffer User List User ListUser settings menu User SettingsOption Description Port accessCopy User Settings Local KeyPad PIN Defines the PIN number for Local Advanced SettingsChange administrator password Setting Description ValueLoad new firmware Save current firmware FirmwareFunction Description Serimux is waiting to save its firmware User Controls User Accessible host list screenUser main menu User main menuPort List screen Limited user accessible Port list¾ Port info User Terse modeTerse mode commands ¾ Connect to port ¾ Accessible host list¾ User Logout System Reset button¾ Verbose mode Firmware upload window Firmware UpgradeLast confirmation before firmware update Action from Keypad Reaction of Serimux Login the administratorKeypad Control Functions of the KeypadLogin user to a port Login a user to the administrator main menuAction from Keypad Disconnect and logout a userConnect 2 host ports To detach a modem Reset Serimux Console Switch to default settingsDisconnect 2 ports How To Setup The Terminal Using the TerminalChanging The Terminal Operating Parameters F1- Disp Setup MenuF2- Genrl Setup Menu Printer F3- Keybd Setup MenuF4- Comm Setup Menu Printer RCV ON/OFF F5- Misc Setup MenuF7- FKeys SET-UP Definition Setup Menu F6-Tabs SET-UP MenuProgrammable Keys F9- Lan Setup MenuF8- Ansbk SET-UP Menu F10- Colr1 Set-up MenuOption Color Association = OFF/ON Color Setup MenuF11- Colr2 Set-up Menu Attribute = Bold/BlinkPalette Display Attribute Foreground Color Background Color Color PalettesColor Palettes Contd Command Enhanced PC Local Keyboard CommandsWyse Terminal Command GuideCommands Supported in Ascii Personalities SameKey/fkey DEL Native Mode WyseSelect bell volume Stop parity wordMessage CR Sequence DELKey/fkey Sequence Sequence DEL ESC . cursor1Bcolor map ESC a mf attrAttr FcolorCcc C ColLine col Sending data Editing ContdClearing Data Pp bb...bb Print FunctionsCharacter Sets SetVariable Values for Commands Variable Values for Commands Contd Max Maximum Speed LengthLine/Column DefinitionParity Bits Bell VolumeFunction Key Palette Color PalletteSupported VT100,VT220 and Console Ansi Commands Ansi Command Guide1 VT100, VT220 and Console Ansi Command Guide Label assigned Supported VT100, VT220 and Console Ansi Commands, ContdCharacter Set Selection ESC Ps finalCharacter Attribute Supported VT100, VT220 and Console Ansi Commands ContdFinal character Values for Ps aboveEditing Functions Values for Psn in table onShifted function key See tables below an on next page for values Kc/hc ST StringClear Key Lock Values of Fn for Numeric Keypad keys Redefine keys with stringUnshifted function key Key ValueTransmission/Printer Control More Terminal Control CommandsTerminal Resets Auxiliary Keypad ModesKeyboard Language 2 VT52 Command GuideCommand VT52 See table below for values of PsBasic Setup Using Printer Server via Ethernet ConnectionSetup for LPD Tftp Printing Setup for TftpLPD printing Hardware Information Hardware Specifications TerminalHardware Specifications Serimux Serial Port Pinouts Pin assignment at Wire Color Standard End Crossed EndCPU-to-RACKMUX Ethernet Crossover Cable Serial Port CablingCable Adapters RJ45 SignalDB25F Mating face of an RJ45 Female Terminal Connector Pin AssignmentsSUB-D Female connector 3 4Administrator Appendix a Serimux Port CharacteristicsDescription Acceptable Value Default Value Appendix B Serimux User and Administrator CharacteristicsIndex Warranty Information