Quatech manual Default DSE-410D Settings, Dhcp

Page 10

Step 2: Attach the DSE-410D to your network’s switch or hub using a standard Cat 5 Ethernet cable, or directly to the LAN port on your computer using a crossover cable. You can connect your serial devices now if needed.

If using Telnet for setup, refer to the Console mode section, Chapter 9, and Chapter 5, then power up the DSE-410D.

Step 3: If using Windows, install the Quatech DSE-410D Manager software on the configuring Computer.

Step 4: Power on the DSE-410D and check the status lights.

Step 5: Start the Quatech DSE-410D Manager from your program menu.

Step 6: Select Search to find the DSE-410D on your network.

Step 7: When found, Double-Click the DSE-410D to bring up the Server Properties Configuration Screen. If more than one DSE-410D shows up, select the one that matches the Default IP Address shown on the bottom of the DSE-410D (usually 192.168.0.1).

Step 8: Refer to the Server Properties section, Chapter 5 for details on the Configuration parameters for each field. Configure and then Save/Update.

Step 9: If you want to use Virtual COM ports with Windows, install the Virtual COM port or ports on each computer requiring access to the DSE-410D.

Default DSE-410D Settings

Server Name:

Quatech

Serial Number:

 

Password:

Blank

DHCP:

Disable

IP Address:

192.168.0.1

Net Mask:

255.255.255.0

Gateway:

192.168.0.254

MAC Address Fixed – see bottom label

Baud Rate:

9600

Data/Parity/Stop:

8-N-1

Flow Control:

None

TCP/UDP Ports:

TCP Port 1 – 4000, Port 2 - 4001

Connection Mode:

Server

Remote IP Address:

255.255.255.255

 

 

4

DSE-410D Owner’s Manual – Document Number: 940-0186-100

Quatech, Inc. - 5675 Hudson Industrial Parkway, Hudson, OH 44236 – 330.655.9000

http://www.quatech.com

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model DSE-410D World HeadquartersPage Table of Contents Searching LAN for DSE-410D Server Name PasswordMAC Address Installing Virtual Com Port Page Features IntroductionVirtual COM Mode Direct IP ModeCommunication Modes Heart Beat Connection Quick StartDefault DSE-410D Settings DhcpSpecifications Optional Accessories DimensionsConfiguration Options Ethernet Connection Side View when vertically mountedHardware Light IndicationMode Switches DSE-410D Server Port Power ConnectionReset Button Top ViewRS-232 Mode RS-485 ModeRS-422 Mode Default SettingSerial Connections RS-232 Connections RS-422 Connections RS-485 Connections Page Install Quatech DSE-410D Software Page Page Page Using DSE-410D Manager Searching LAN for DSE-410DUninstall Virtual COM Firmware UpgradeVirtual COM Configuration Searching ServerStatus ProtocolCOM Name Server Properties ScreenNext chapter Server Properties Configuration Server Name PasswordIP Address, Netmask, and Gateway Properties Server Serial Port Select 1 or Link Status Shown in Telnet or Console mode onlyMAC Address Baud Rate Set for each portTCP/UDP Protocol Set for each port Connection Mode Set for each portFlow Control Set for each port TCP/UDP Port Set for each portUpdate Page Installing Virtual Com Port Page Page Use Device Manager to View New Ports Page Page Removing a Virtual Com Port Removing the Virtual COM Port using Device Manager Page Page Upgrade Mode Using Virtual COM or Serial ConnectionsPage Page Page Console Mode Setup Page Appendix a RS-232, RS-422 Loopback Connections Page Appendix B RS-232 Connections DB9MRS-232 Connections cont’d Signal Name Direction Pin Appendix C RS-422 ConnectionsRS-422 Connections cont’d Appendix D RS-485 Connections Page Appendix E Warranty Date of Purchase Model Number
Top Page Image Contents