Polycom 6400-S manual Field Description

Page 34

User Guide V2IU 6400-S Converged Network Appliance

Field	Description

SIP Register pacing	If the SIP Expires override field is set to a
	lower value, the number of registration
	messages may overload the soft-switch.
	In order to prevent this, you can set the
	SIP Register pacing field to the number of
	seconds to wait before forwarding a
	register message from one phone to the
	soft-switch. Any register messages
	received before this time will be locally
	answered by the 6400-S. For example,
	you may set the expires value to 60 and
	the pacing value to 1800 to have the
	phone register to the 6400-S every
	minute, but only let a register message
	through to the soft-switch every 30
	minutes.

TFTP Server IP Address	Enter the IP address for the TFTP Server.

This allows the 6400-S to forward
(proxy) TFTP requests from devices
on the Subscriber side to a TFTP
server on the Provider side.

H232 Gatekeeper IP Address	If an H.323 ALG is needed, enter the
	address (either an IP or URL) for the
	H.323 Gatekeeper. This address should
	be reached via the Provider side Ethernet
	port.

Use ALG Alias IP Addresses	Not used

ALG Subscriber Interface	Not Used.

Automatic MCCP Re-registration	Automatic MGCP Re-registration is used
	to re-register MGCP endpoints every time
	the network or system restarts. Enable
	this feature to automatically synchronize
	the softswitch and phones immediately
	after a restart. The default is Enabled.

MGCP Re-registration Rate(s)	The MGCP Re-registration Rate is used to
	set the number of MGCP RSIP messages
	to send per second to the Media Gateway
	Controller when re-registration is needed.
	If the MGCP Re-registration Rate needs to
	be changed, enter a value between 1 and
	5. Generally, this value does not need to
	be modified. The default value is 5
	msg/second.

5 - 4

Image 34

Contents User Guide V2IU 6400-S Converged Network Appliance Trademark Information Contents Configuring the Firewall Configuring Network SettingsConfiguring VoIP Administrative OptionsContents User Guide V2IU 6400-S Converged Network Appliance Introduction Introducing the V2IU 6400-S Converged Network ApplianceService Provider E-1NxT-1/E-1 Branch Office Features Physical Connections and SpecificationsManagement Features User Guide V2IU 6400-S Converged Network Appliance Physical Installation1 Installing the 6400-SIf AC power supplies are installed If DC power supplies are installed Power Supplies1 DC Power Supply Interface RequirementsAC Power Supply Interface Requirements DC Power Supply LED IndicatorsConfiguring the V2IU 6400-S Connecting to the 6400-SUser Guide V2IU 6400-S Converged Network Appliance Navigating through the configuration pages Logging in and out of the 6400-SGetting help Getting information about the networkRouting Information Getting information about the system System uptime Recent Call Log Configuring Network Settings Configuring subscriber interface settingsConfiguring provider interface settings Setting the Ethernet link rate Link speed and duplex with locally attached devices Configuring the Network Setting DescriptionTo configure network settings Configuring VoIP To configure VoIP ALG Configuring VoIP Field Description Currently registered Configuring VoIP subnet routing Deleting a VoIP subnet route Configuring VoIP survivability Configuring sofswitch survivabilitySoftswitch redundancy configuration Configuring Vrrp To configure Sofswitch Redundancy, enter the followingConfiguring VoIP User Guide V2IU 6400-S Converged Network Appliance Configuring the Firewall Configuring the firewall basic settingsTo configure basic settings Configuring advanced firewall settings Basic settings rulesAdvanced setting rules Enabling or disabling the firewallAdministrative Options Changing the administration passwordSpecifying user commands Managing SIP, Mgcp or H.323 clients Selecting a client Deleting clientsQuerying clients Adding clientsUsing Network Test Tools Rebooting the systemRestarting the network Running a ping test Running a traceroute testUpgrading the firmware Configuring a management interface Configuring the interfaceReconnecting the 6400-S Configuring the trusted management addresses Move the connection from Port 2 to PortSetting the Provider MTU size Enabling Snmp Field Description Disabling Snmp Enabling remote system loggingAddressport Setting the system date and time Disabling remote system loggingCreating a static route Deleting a static route User Guide V2IU 6400-S Converged Network Appliance Appendix Troubleshooting TipsTrouble accessing the Internet No dial tonePinging the softswitch Telephone doesnt register with the softswitchChecking the configurations on the ALG Checking the ALG registration codeImportant Safeguards Regulatory NoticesOther Rights and Limitations Regulatory Notices Warranty and Warranty Exclusions Regulatory Notices Miscellaneous Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices Compliance and Compatibility1 Regulatory Notices